TDK GENESYS 750W HALF RACK - Manual (Page 17)

83-507-5002 Rev. B
9
CHAPTER 2 SPECIFICATIONS
2.1 OUTPUT RATING
MODEL
GEN 6-100 8-90 12.5-60 20-38 30-25 40-19 – 60-12.5 80-9.5 100-7.5 150-5 300-2.5 600-1.3
1.Rated output voltage (*1) V 6 8 12.5 20 30 40 – 60 80 100 150 300 600
2.Rated output current 750W (*2) A 100 90 60 38 25 19 – 12.5 8.5 7.5 5 2.5 1.3
3.Rated output power 750W W 600 720 750 760 750 760 – 750 760 750 750 750 780
MODEL GEN 6-200 8-180 12.5-120 20-76 30-50 40-38 50-30 60-25 80-19 100-15 150-10 300-5 600-2.6
1.Rated output voltage (*1) V 6 8 12.5 20 30 40 50 60 80 100 150 300 600
2.Rated Output Current 1500W (*2) A 200 180 120 76 50 38 30 25 19 15 10 5 2.6
3.Rated output power 1500W W 1200 1440 1500 1520 1500 1520 1500 1500 1520 1500 1500 1500 1560
2.2 INPUT CHARACTERISTICS V 6 8 12.5 20 30 40 50 60 80 100 150 300 600
1. Input voltage/freq. (*3) –
2. Input current (at 100/200Vac) A
3. Power Factor –
4. 750W models Efficiency (*4) % 76/78 77/80 81/84 82/85 82/85 83/87 83/87 83/87 83/87 83/87 83/87 83/87 83/87
5. 1500W models Efficiency (*4) % 77/79 78/81 82/85 83/86 83/86 84/88 84/88 84/88 84/88 84/88 84/88 84/88 84/88
6. Inrush current at 100/200V A
2.3 CONSTANT VOLTAGE MODE V 6 8 12.5 20 30 40 50 60 80 100 150 300 600
1. Max.Line regulation (*5) –
2. Max.Load regulation (*6) –
3. Ripple and noise (p-p,20MHz) (*10) mV 60 60 60 60 60 60 60 60 80 80 100 150 300
4. Ripple r.m.s., 5Hz~1MHz (*10) mV 8 8 8 8 8 8 8 8 8 8 10 25 60
5. Temperature coefficient PPM/°C 100PPM/°C of rated output voltage, following 30 min utes warm up
6. Temperature drift –
7. Rem. Sense compensation/wire V 1 1 1 1 1.5 2 2 3 4 5 5 5 5
8. Up-prog. Response time 0~Vomax (*9) mS 250
9. Down-prog. Response time: Full load mS 10 250
No load 500 600 700 800 900 1000 1100 1100 1200 1500 2000 2500 4000
10. Transient response time mS
11. Hold-up time mS
2.4 CONSTANT CURRENT MODE V 6 8 12.5 20 30 40 50 60 80 100 150 300 600
1. Max.line regulation (*5) –
2. Max.load regulation (*7) –
3. Ripple r.m.s. 5Hz~1MHz.750W (*8) mA 200 180 120 76 63 48 – 38 29 23 18 13 8
1500W (*8) mA 400 360 240 152 125 95 75 75 57 45 35 25 12
4. Temperature coefficient PPM/°C
5. Temperature drift –
2.5 ANALOG PROGRAMMING AND MONITORING
1.Vout voltage programming
–
2. Iout voltage programming –
3. Vout resistor progrmming –
4. Iout resistor programming –
5. On/off control –
6. Output current monitor –
7. Output voltage monitor –
8. Power supply OK signal –
9. Parallel operation –
10. Series operation –
11. CV/CC inicator –
12. Enable/Disable –
13. Local/Remote analog control –
14. Local/remote analog indicator –
85~265Vac continuous, 47-63Hz, single phase.
10.5/5 for 750W model, 21/11 for 1500W models.
0.99@100/200Vac, rated output power.
Less than 25A for 750W models, 50A for 1500W models.
0.01% of rated output voltage +2mV
0.01% of rated output voltage +2mV
0.05% of rated Vout over 8hrs interval following 30 minutes warm-up. Constant line, load & temp.
80 150
50 80 150
Time for the output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated
output current.
Output set-point: 10~100%.
Less than 1mS for models up to and including 100V; 2mS for models above 100V.
More than 20mS, 100Vac, rated output power.
0.01% of rated output voltage +2mA
0.02% of rated output current +5mA
100PPM/°C from rated output current, following 30 m inutes warm-up.
0.05% of rated lout over 8hrs interval following 30 minutes warm-up. Constant line, load & temp.
0~100%, 0~5V or 0~10V, user select. Accuracy and linearity; +/-0.5% of rated Vout.
0~100%, 0~5V or 0~10V, user select. Accuracy and linearity; +/-1% of rated Iout.
0~100%, 0~5/10Kohm full scale, user select. Accuracy and linearity: +/-1% of rated Vout.
0~100%, 0~5/10Kohm full scale, user select. Accuracy and linearity: +/-1.5% of rated Iout.
By electrical Voltage: 0~0.6V/2~15V or dry contact, user selectable logic.
0~5V or 0~10V, user selectable. Accuracy: 1%
0~5V or 0~10V, user selectable. Accuracy: 1%
4~5V-OK, 0V-Fail, 500ohm series resistance.
Possible, up to 4 units in master/slave mode with single wire current balance connection.
Possible (with external diodes), up to 2 units.
CV: TTL high (4~5V), source current: 10mA, CC: TTL low (0-0.6V). Sink current: 10mA .
Dry contact. Open: off, Short: on. Max. voltage at Enable/Disable in: 6V.
By electrical signal or Open/Short: 0~0.6V or short: Remote, 4~5V or open: Local.
Open collector. Local: Open, Remote: On. Maximum voltage: 30V, maximum sink current: 5mA.