Onkyo HT-RC180 - Manual (Page 12)

12
Front & Rear Panels
—Continued
SIRIUS antenna
(TX-NR807: North American models)
This jack is for connecting a SIRIUS Satellite Radio
antenna, sold separately (see the separate SIRIUS
instructions).
MONITOR OUT
These S-Video and composite video jacks should be
connected to a video input on your TV or projector.
HDMI IN 1–6 and OUT (TX-NR807)
HDMI IN 1–5 and OUT (HT-RC180)
HDMI (High Definition Multimedia Interface) con-
nections carry digital audio and digital video.
The HDMI inputs are for connecting components
with an HDMI output, such as a DVD player, Blu-
ray Disc Player, DVD recorder, or DVR (digital
video recorder). They’re assignable, which means
you can assign each one to an input selector to suit
your setup. See “HDMI Input Setup” on page 48.
The HDMI output is for connecting a TV or projec-
tor with an HDMI input.
COMPONENT VIDEO IN 1 and 2
These RCA component video inputs are for con-
necting components with a component video out-
put, such as a DVD player, DVD recorder, or DVR
(digital video recorder). They’re assignable, which
means you can assign each one to an input selector
to suit your setup. See “Component Video Setup”
on page 49.
COMPONENT VIDEO MONITOR OUT
These RCA component video outputs are for con-
necting a TV or projector with a component video
input.
FM ANTENNA
This jack is for connecting an FM antenna.
AM ANTENNA
These push terminals are for connecting an AM
antenna.
IR IN/OUT (TX-NR807)
A commercially available IR receiver can be con-
nected to the IR IN jack, allowing you to control the
AV receiver while you’re in Zone 2/3, or control it
when it’s out of sight, for example, installed in a
cabinet.
A commercially available IR emitter can be con-
nected to the IR OUT jack to pass IR (infrared)
remote control signals through to other components.
12V TRIGGER OUT ZONE 2 (TX-NR807)
This output can be connected to the 12-volt trigger
input on a component in Zone 2. When Zone 2 is
turned on, a 12-volt trigger signal is output.
12V TRIGGER OUT ZONE 3 (TX-NR807)
This output can be connected to the 12-volt trigger
input on a component in Zone 3. When Zone 3 is
turned on, a 12-volt trigger signal is output.
AC INLET
The supplied power cord is connected here. The
other end of the power cord should be connected to
a suitable wall outlet.
GND screw
This screw is for connecting a turntable’s ground
wire.
PHONO IN
These analog audio inputs are for connecting a turn-
table.
CD IN
These analog audio inputs are for connecting a CD
player’s analog audio output.
TV/TAPE IN/OUT
These analog audio inputs and outputs are for con-
necting a TV or recorder with an analog audio input
and output (cassette, Mini Disc, etc.).
GAME IN
Here you can connect a game console, etc. Input
jacks include S-Video, composite video, and analog
audio.
CBL/SAT IN
Here you can connect a cable/satellite receiver, set-
top box, etc. Input jacks include S-Video, composite
video, and analog audio.
VCR/DVR IN/OUT
Here you can connect a VCR or DVR (digital video
recorder). Input and output jacks include S-Video,
composite video, and analog audio.
DVD/BD IN
Here you can connect a DVD/BD player. Input
jacks include S-Video, composite video, and analog
audio. You can connect a DVD/BD player’s 2-chan-
nel analog audio output.
PRE OUT: FRONT L/R, CENTER, SURR L/R,
and SURR BACK L/R
These multichannel analog audio outputs can be
connected to the analog audio input on a multichan-
nel power amplifier for when you want to use the
AV receiver solely as a preamplifier.
PRE OUT: SUBWOOFER
These analog audio outputs can be connected to a
powered subwoofer. You can connect the powered
subwoofer with two PREOUT: SUBWOOFER
jacks respectively. The same signal is output from
each jack.
PRE OUT: ZONE 2, ZONE 3 L/R
These analog audio outputs can be connected to the
line inputs on amplifiers in Zone 2 and Zone 3.
TX-NR807_En.book Page 12 Tuesday, July 28, 2009 12:00 PM