Onkyo TX-SR605 - Manual (Page 96)

96
Troubleshooting—Continued
• If the video source is connected to a component video
input, your TV must be connected to the COMPO-
NENT VIDEO OUT or HDMI OUT (page 25).
• If the video source is connected to an HDMI input,
your TV must be connected to the HDMI OUT
(page 25).
• While the Pure Audio listening mode (not North
American models) is selected, the video circuitry is
turned off and only video signals input through HDMI
IN can be output.
• On your TV, make sure that the video input to which
the AV receiver/AV amplifier is connected is selected.
There’s no picture from a source connected to
an HDMI IN
• If the message “Resolution Error” appears on the AV
receiver/AV amplifier’s display, this indicates that the
TV or display does not support the current video reso-
lution and you need to select another resolution on
your DVD player.
The onscreen menus don’t appear
• The onscreen menus may do not appear on a TV that’s
connected to the HDMI OUT. When the HDMI Mon-
itor Out is set to No (page 47), the onscreen menus are
output at a resolution of 480i. If the onscreen menus
do not appear, set the HDMI Monitor Out to Yes
(page 47).
• Make sure that the video settings are correct (page 48).
• On your TV, make sure that the video input to which
the AV receiver/AV amplifier is connected is selected.
The immediate display does not appear
• The immediate display appears on a device connected
to the COMPONENT VIDEO OUT, when the Com-
ponent Video Setup (page 49) is set to “---.”
• If both of the HDMI Video Setup (page 48) and the
Component Video Setup (page 49) are set to “---,” the
immediate display is output to a device connected to
the HDMI OUT.
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear
• Relocate your antenna.
• Move the AV receiver away from your TV or com-
puter.
• Listen to the station in mono (page 57).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
• Make sure that the batteries are installed with the cor-
rect polarity (page 12).
• Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 12).
• Make sure that the remote controller is not too far
away from the AV receiver/AV amplifier, and that
there’s no obstruction between the remote controller
and the AV receiver/AV amplifier’s remote control
sensor (page 12).
• Make sure that the AV receiver/AV amplifier is not
subjected to direct sunshine or inverter-type fluores-
cent lights. Relocate if necessary.
• If the AV receiver/AV amplifier is installed in a rack
or cabinet with colored-glass doors, the remote con-
troller may not work reliably when the doors are
closed.
• Make sure you’ve selected the correct remote control-
ler mode (pages 13-16).
• When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
• Make sure you’ve entered the correct remote control
code.
• Make sure to set the same ID on both the AV receiver/
AV amplifier and remote controller (pages 83 and 86).
Can’t control other components
• If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an
cable won’t work (page 39).
• Make sure you’ve selected the correct remote control-
ler mode (pages 13-16).
• If you’ve connected an -capable Onkyo MD
recorder, CD recorder, Dock to the TAPE IN/
OUT jacks, or an Dock to the GAME/TV IN
jacks, for the remote controller to work properly, you
must set the display to MD, CDR, or DOCK (pages 51
and 91).
• To control another manufacturer’s component, point
the remote controller at that component.
• To control an Onkyo component that’s connected via
, point the remote controller at the AV receiver/AV
amplifier. Be sure to enter the appropriate remote con-
trol code first (page 91).
• To control an Onkyo component that’s not connected
via , or another manufacturer’s component, point
the remote controller at the component. Be sure to enter
the appropriate remote control code first (page 90).
Tuner (TX-SR605 only)
Remote Controller