Midi implimentation, Channel voice messages, Polyphonic key pressure – Roland TD-10 User Manual
Page 154: Control change
Section 1. Receive data
■
Channel Voice Messages
*
Following Channel Voice Messages can be recorded in SETUP MIDI TX/RX Channel.
●
Note Off
Status
2nd byte
3rd byte
8nH
kkH
vvH
9nH
kkH
00H
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
kk = note number:
00H - 7FH (0 - 127)
vv = note off velocity:
00H - 7FH (0 - 127)
*
In the Drum part, ignored This message.
*
The Velocity Values of Note Off message are ignored.
*
When recording, this is recorded in the sequencer data itself.
●
Note On
Status
2nd byte
3rd byte
9nH
kkH
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
kk = note number:
00H - 7FH (0 - 127)
vv = note on velocity:
00H - 7FH (0 - 127)
*
A channel which is assigned to the drum part will receive only the note numbers which
are specified by the drum kit or the percussion group.
*
When recording, this is recorded in the sequencer data itself.
●
Polyphonic Key Pressure
Status
2nd byte
3rd byte
AnH
kkH
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
kk = note number:
00H - 7FH (0 - 127)
vv = Value:
00H - 7FH (0 - 127)
Initial value = 00H (0)
*
A channel which is assigned to the drum part will receive only the note numbers which
are specified by the drum kit.
*
If the value is greater than 40H (64), the decay of the note sounded by the received note
number will be shortened.
*
Not recorded in the sequencer.
●
Control Change
❍
Modulation (Controller number 1)
Status
2nd byte
3rd byte
BnH
01H
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Modulation depth:
00H - 7FH (0 - 127)
Initial value = 00H (0)
*
Only the channel assigned to the drum part can be received.
*
If the SETUP MIDI CTRL settings Pedal CC or Zone CC are set to MODULATION, the
effect will apply to the specified parameter.
*
During recording, this will be recorded in the sequencer data as Pedal Ctrl Chg data or
Zone Ctrl Chg data.
❍
Foot Control (Controller number 4)
Status
2nd byte
3rd byte
BnH
04H
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
Initial value = 00H (0)
*
Only the channel assigned to the drum part can be received.
*
The effect will be obtained when SETUP MIDI CTRL Pedal CC is set to FOOT CON-
TROL.
*
When recording, this will be recorded as Pedal Ctrl Chg data in the sequencer data
itself.
❍
Data Entry MSB (Controller number 6)
Status
2nd byte
3rd byte
BnH
06H
mmH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
mm = Control value:
00H - 18H (0 - 24semitone)
Initial value = 02H (2 semitone)
*
If RPN was previously specified as 00H 00H (Pitch Bend Sensitivity), you can specify
the pitch bend sensitivity. This can be specified in semitone steps up to a maximum of 2
octaves. (Refer to the RPN item.)
*
In the Drum part, ignored This message.
*
Not recorded in the sequencer.
❍
Volume (Controller number 7)
Status
2nd byte
3rd byte
BnH
07H
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Volume:
00H - 7FH (0 - 127)
*
Volume messages are used to adjust the volume balance of each track.
*
Not recorded in the sequencer.
❍
Pan (Controller number 10)
Status
2nd byte
3rd byte
BnH
0AH
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = pan:
00H - 40H - 7FH (Left - Center - Right)
*
In the Drum part, ignored This message.
*
Not recorded in the sequencer.
❍
General purpose controller 1 (Controller number 16)
Status
2nd byte
3rd byte
BnH
10H
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
Initial value = 00H (0)
*
Only the channel assigned to the drum part can be received.
*
If the SETUP MIDI CTRL settings Pedal CC or Zone CC are set to General Purpose
Controller 1, the effect will apply to the specified parameter.
*
During recording, this will be recorded in the sequencer data as Pedal Ctrl Chg data or
Zone Ctrl Chg data.
❍
General purpose controller 2 (Controller number 17)
Status
2nd byte
3rd byte
BnH
10H
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
Initial value = 00H (0)
*
Only the channel assigned to the drum part can be received.
*
If the SETUP MIDI CTRL settings Pedal CC or Zone CC are set to General Purpose
Controller 2, the effect will apply to the specified parameter.
*
During recording, this will be recorded in the sequencer data as Pedal Ctrl Chg data or
Zone Ctrl Chg data.
❍
Hold 1 (Controller number 64)
Status
2nd byte
3rd byte
BnH
40H
vvH
n = MIDI channel number:
0H - FH (ch.1 - ch.16)
vv = Control value:
00H - 7FH (0 - 127)
0-63 = OFF, 64-127 = ON
*
In the Drum part, ignored This message.
*
When recording, this is recorded in the sequencer data itself.
MIDI Implimentation
154
May. 1 1997
Model TD-10
Version 1.00