Siemens CP 243-2 - Manual (Page 51)

Access to the Data of the AS-i Slaves
3-3
SIMATIC NET CP 243-2 AS-i Master
C79000-G8976-C142/02
Assignment of the AS-i Input Data of the Standard or A Slaves (Bank 0 in the
Analog Input Area of the CP)
Bank Byte no. Bit 7–4 Bit 3–0
0 m+0 reserved Slave 1 or slave 1A
Bit 3 | Bit 2 | Bit 1 | Bit 0
0 m+1 Slave 2 or slave 2A Slave 3 or slave 3A
0 m+2 Slave 4 or slave 4A Slave 5 or slave 5A
0 m+3 Slave 6 or slave 6A Slave 7 or slave 7A
0 m+4 Slave 8 or slave 8A Slave 9 or slave 9A
0 m+5 Slave 10 or slave 10A Slave 11 or slave 11A
0 m+6 Slave 12 or slave 12A Slave 13 or slave 13A
0 m+7 Slave 14 or slave 14A Slave 15 or slave 15A
0 m+8 Slave 16 or slave 16A Slave 17 or slave 17A
0 m+9 Slave 18 or slave 18A Slave 19 or slave 19A
0 m+10 Slave 20 or slave 20A Slave 21 or slave 21A
0 m+11 Slave 22 or slave 22A Slave 23 or slave 23A
0 m+12 Slave 24 or slave 24A Slave 25 or slave 25A
0 m+13 Slave 26 or slave 26A Slave 27 or slave 27A
0 m+14 Slave 28 or slave 28A Slave 29 or slave 29A
0 m+15 Slave 30 or slave 30A
Bit 3 | Bit 2 | Bit 1 | Bit 0
Slave 31 or slave 31A
Bit 3 | Bit 2 | Bit 1 | Bit 0
m = start address of the CP analog module in the input direction
Assignment of the AS-i Output Data of the Standard or A Slaves (Bank 0 in the
Analog Output Area of the CP)
Bank Byte no. Bit 7–4 Bit 3–0
0 n+0 reserved Slave 1 or slave 1A
Bit 3 | Bit 2 | Bit 1 | Bit 0
0 n+1 Slave 2 or slave 2A Slave 3 or slave 3A
0 n+2 Slave 4 or slave 4A Slave 5 or slave 5A
0 n+3 Slave 6 or slave 6A Slave 7 or slave 7A
0 n+4 Slave 8 or slave 8A Slave 9 or slave 9A
0 n+5 Slave 10 or slave 10A Slave 11 or slave 11A
0 n+6 Slave 12 or slave 12A Slave 13 or slave 13A
0 n+7 Slave 14 or slave 14A Slave 15 or slave 15A
0 n+8 Slave 16 or slave 16A Slave 17 or slave 17A
0 n+9 Slave 18 or slave 18A Slave 19 or slave 19A
0 n+10 Slave 20 or slave 20A Slave 21 or slave 21A
0 n+11 Slave 22 or slave 22A Slave 23 or slave 23A
0 n+12 Slave 24 or slave 24A Slave 25 or slave 25A
0 n+13 Slave 26 or slave 26A Slave 27 or slave 27A
0 n+14 Slave 28 or slave 28A Slave 29 or slave 29A
0 n+15 Slave 30 or slave 30A
Bit 3 | Bit 2 | Bit 1 | Bit 0
Slave 31 or slave 31A
Bit 3 | Bit 2 | Bit 1 | Bit 0
n = start address of the CP analog module in the output direction