MITSUBISHI ELECTRIC WS-48513 - Manual (Page 13)

12 13
Back Panel
�
�
�� �� �� �
��
������� �������
�������� �� ������� ������ ����� ������� ��� � ���� ������� ����� ��������� ���� ����� ���� �� ������� ����� ��������� ���� ������� �� ������� ����� ��� �� �������� �������
�������� ������ ���� ����� ���� ������ ������� ���� �� ��������� �� ������� ����� ��������� �� ��������� ������� ���������� ������� ���� � ���� �� ��� ���� ���� ������ ��� ��������� �������
����� ����������� ���� ������� �������� �������� ���������� ��� ���������� ����� ����� ��� ��������� ��� ����������� ������� ��� ��������� ������ ������� �������� ���������� ��������� �� ��� ������� ������ ���� ���� ����� ����������� ����� ����� �� ��� ����� ����� ����� �� ������� ������ ��� ��������� ���� ������� �� �������
����������� ����������� ���������� ��� ������ ������� ���������� ��
7. MonitorLink™/RS-232C Control
A digital control interface that works in conjunction with
MonitorLink. While MonitorLink provides the digital
video signal, MonitorLink Control provides enhanced
functioning such as automatic power ON/OFF and input
selection. If you are not connecting a Mitsubishi HDTV
Receiver/Controller with MonitorLink features, MonitorLink
Control can be used as an RS-232C control signal
input port with an external control system. Please visit
www.mistubishi-tv.com for RS-232 command protocol.
8. IEEE-1394 Input/Output
These jacks allow the TV to connect to external digital
products by means of a single cable. Three jacks (one
on the front panel and two on the back) are provided for
this purpose, which allow for a high degree of flexibility
for connecting your system together. Please refer to
NetCommand, later in this book for IEEE-1394 device
connection details.
9. Inputs 1-2
These inputs can be used for the connection of a VCR,
Super VHS (S-VHS) VCR, DVD player, standard satellite
receiver or other A/V device to the TV. Please note that if
you connect to the S-VIDEO terminal, the VIDEO terminal
is deactivated. The VIDEO terminal is active when there is
no S-Video connection.
10. Component Inputs 1-2
YPbPr (480i/480p/1080i)
These inputs can be used for the connection of A/V
equipment with component video outputs, such as a DVD
player or external HDTV receiver. Please see Appendix B
for signal compatibility.
11. Input DTV (480i/480p/1080i)
This input is used to connect an external DTV receiver,
and can be configured for YPrPb and RGB plus
H&V signal types. Please see Appendix B for signal
compatibility.
12. Monitor Output (Audio Video 1, Audio 2)
The Monitor Output sends the TV audio and video signals
from Ant-A, Ant-B or Inputs 1-3 to an A/V Receiver or
other analog A/V equipment. Ant-DTV and IEEE 1394
sources will be provided as down converted analog
signals to the Monitor Output jacks.
There will be no video signals from digital products if the
original signals are copy protected. No video signals are
provided from VGA, Component 1 and 2, MonitorLink or
Input-DTV.
For recording with a VCR, use Audio Video 1. When
connecting to an A/V Receiver, use Audio 2. If using the
A/V Receiver with NetCommand, the Audio 2 output will
always be Main, not PIP. If using an A/V Receiver without
NetCommand and Audio 2 is set for PIP audio then the
PIP’s or POP’s audio signal is sent to an amplifier or
wireless headphones. If no PIP or POP is displayed, the
output will not send audio.
13. VGA Video and VGA Audio
This input can be used for the connection of a computer.
Please see Appendix B for signal compatibility.