Gianni Industries VDH-100 - Manual (Page 4)

VDH-100
Full Color Villa Video Door Phone
GIANNI INDUSTRIES, INC.
The products are manufactured under an ISO
9 0 0 1
Q C 0 8 0 0 0 0 C e r t i f i e d Q u a l i t y
Management Program environment back its
product quality, performance and commitment
to customer satisfaction.
&
The product is warranted against defects in material and
workmanship while used in normal service for a period of 1
year from the date of sale to the original customer. The GEM
policy is one of continual development and improvement;
therefore GEM reserves the right to change specifications
without notice.
Warranty
Operation Instruction
The Master Code is set to 1234 as factory default.
Enter Programming Mode Setting the relocking timer
Delete all PIN Codes
Add PIN codes
Delete a PIN Code
Change the Master code
Exiting from the program mode
Compose twice the master code (Factory
master is
1234 ) 「 」
→ → an audible and the LED will flash red you are now in the
"programming mode".
Factory default set is 0.5 second.
Enter the Programming mode Enter 99
Enter the desired lock / relay operation time in a
two digit format (01~99 seconds)
Press #
t o e x i t f r o m t h e p r o g r a m m i n g m o d e , o r
programming other operating.
→ 「＊ 」→
→ 「 」
The lockout facility
will operate.
Enter the Programming mode Press 88 The red LED
will remain on.) Press 0000 The red LED turn off,
beep Indicate that the delete all PIN codes.
→ 「 ＊ 」(
→ 「 」 (
)→
1. Do not put the outdoor sation near the magnetic area such
as televison, video recorder etc.
2. Do not drop, knock or shake the unit.
3. Do not put the
outdoor sation in hot areas, high
temperatures can shorted the life of electronic device.
4. Do not attempt to open the unit, non expert handing may
damage the unit.
5. Keep the indoor monitor dry, humidity and all types of
liquids or moisture contains mineral that will corrode
electronic circuits.
6.Do not use the wet dishcloth or the volatile cleansers to
clean it.
7. The installation position of outdoor station and indoor
monitor should be about 150 cm height.
8. Power must be shut off when installing.
Enter the Programming mode, Enter the slot position code
01~40 ???? Input 4 digit PIN codes (beep) enrolled.
Press # to exit from the programming mode, or program
other operating.
Note : The codes 0000 , 1234 or master code are not be
used for PIN code.
「 」 → →
「 」
「 」 「 」
＊
Enter the Programming mode Press the slot position code of
your choice to delete (example "06") Press 06
0000 beep) delete Press # to exit from the
programming mode, or programming other operating.
→
→ 「 ＊ 」 →
「 」 ( → → 「 」
Enter the Programming mode, Enter the slot position code
00 Enter the 「＊ 」→
→
「????」 new master code he long beep
sound heard The new Master code is set.
t
Remove power from the unit and hold down the key.
Apply power whilst holding button down, the unit will then give
long continuous tone. When the tone has stopped,
Press
00# The Master code reset to Factory 1234 .
「 ＊ 」 →
→
「＊ 」→ 「 」
Press # to exit from the programming mode. 「 」
The system will out of the programming
Care and maintenance
Master Code reset to Factory 1234 「 」
Copyright 2008 Gianni industries, inc. All rights reserved.
DM-CA-VDH-100 Ver. A Published on 2008.09.03
No. 13, Zhong Sing Road, Tu-Cheng Industrial Zone,
Tu-Cheng City, Taipei, Taiwan 23678
Tel: 886-2 2267 7986 / Fax: 886-2 2267 9876
E-Mail: [email protected]
Website: gianni.tw