FUJITSU MCJ3230AP User Manual
FUJITSU Hardware
Table of contents
Document Outline
- Front Cover
- FOR SAFE OPERATION
- Revision History
- Preface
- DISCLAIMER
- Important Alert Items
- REFERENCED STANDARDS
- Contents
- CHAPTER 1 General Description
- CHAPTER 2 Specifications
- CHAPTER 3 Installation Requirements
- CHAPTER 4 Host Interface
- 4.1 Pin Assignment
- 4.2 Signal Description
- 4.3 Interface Registers
- 4.3.1 I/O registers
- 4.3.1.1 Alternate Status register
- 4.3.1.2 ATA Command register
- 4.3.1.3 Data register
- 4.3.1.4 Device Control register
- 4.3.1.5 Drive Address register
- 4.3.1.6 ATAPI Byte Count register
- 4.3.1.7 ATAPI Block Device Select register
- 4.3.1.8 Error register
- 4.3.1.9 ATA Features register
- 4.3.1.10 ATAPI Features register
- 4.3.1.11 ATA Sector Count register
- 4.3.1.12 ATAPI Interrupt Reason register
- 4.3.1.13 Sector Number register
- 4.3.1.14 ATAPI Status register
- 4.3.1 I/O registers
- 4.4 Various Processes
- 4.5 ATA Commands
- 4.5.1 CHECK POWER MODE (E5h)
- 4.5.2 DEVICE RESET (08h)
- 4.5.3 EXECUTE DEVICE DIAGNOSTIC (90h)
- 4.5.4 FLUSH CACHE (E7h)
- 4.5.5 GET MEDIA STATUS (DAh)
- 4.5.6 IDENTIFY PACKET DEVICE (A1h)
- 4.5.7 IDLE IMMEDIATE (E1h)
- 4.5.8 NOP (00h)
- 4.5.9 PACKET (A0h)
- 4.5.10 SET FEATURES (EFh)
- 4.5.11 SLEEP (E6h)
- 4.5.12 STANDBY IMMEDIATE (E0h)
- 4.6 Packet Commands
- 4.6.1 ERASE command
- 4.6.2 FORMAT UNIT command
- 4.6.3 INQUIRY command
- 4.6.4 MODE SELECT (6) command
- 4.6.5 Mode Select (10) command
- 4.6.6 MODE SENSE (6) command
- 4.6.7 MODE SENSE (10) command
- 4.6.8 PREVENT/ALLOW MEDIUM REMOVAL command
- 4.6.9 READ (10) command
- 4.6.10 READ CAPACITY command
- 4.6.11READ FORMAT CAPACITIES command
- 4.6.12 READ DEFECT DATA (10) command
- 4.6.13 READ DEFECT DATA (12) command
- 4.6.14 READ LONG command
- 4.6.15 RECEIVE DIAGNOSTIC RESULTS command
- 4.6.16 REQUEST SENSE command
- 4.6.17 SEND DIAGNOSTIC command
- 4.6.18 SEEK command
- 4.6.19 START/STOP UNIT command
- 4.6.20 SYNCHRONIZE CACHE command
- 4.6.21 TEST UNIT READY command
- 4.6.22 VERIFY command
- 4.6.23 WRITE (10) command
- 4.6.24 WRITE AND VERIFY command
- 4.6.25 WRITE BUFFER command
- 4.6.26 WRITE LONG command
- 4.7 Timing
- 4.7.1 Register/PIO data transfer timing
- 4.7.2 Multiword DMA data transfer timing
- 4.7.3 Ultra DMA data in transfer (initialization timing)
- 4.7.4 Ultra DMA data in transfer (continuous transfer timing)
- 4.7.5 Ultra DMA data in transfer (host stop timing)
- 4.7.6 Ultra DMA data in transfer (device end timing)
- 4.7.7 Ultra DMA data in transfer (host end timing)
- 4.7.8 Ultra DMA data out transfer (initialization timing)
- 4.7.9 Ultra DMA data out transfer (continuous transfer timing)
- 4.7.10 Ultra DMA data out transfer (device stop timing)
- 4.7.11 Ultra DMA data out transfer (host suspend timing)
- 4.7.12 Ultra DMA data out transfer (device end timing)
- 4.7.13 Power-on and Reset Timing
- CHAPTER 5 Operation and Cleaning
- CHAPTER 6 Diagnosis and Maintenance
- Glossary
- Acronyms and Abbreviations
- Index
- READER’S COMMENT FORM
- Back Cover