Fostex VF-16 User Manual
Page 52
52
BPM delay effect parameters (parameter type: BPM DELAY)
For effect types
31
and
32
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
BPM
Adjust the BPM. Range:
30--250 bpm
3.
Note
Select the note value for the delay. Range:
24, 16, 8T, 16...8, 4T, 8., 4, 2T, 4., 2, 2., 1
*
24
= 16th note sextuplets,
16
= 16th notes,
8T
= 8th note triplets,
16.
= dotted sixteenth notes,
8
= 8th notes,
4T
= quarter note triplets,
8.
= dotted eighth notes,
4
= quarter notes,
2T
= half-note triplets,
4.
= dotted quarter notes,
2
= half notes
* The "
.
" shown in the ninth character of the LCD indicates a dotted note.
* The "
T
" shown in the ninth character of the LCD indicates a triplet.
4.
Feedback
Adjust the number of delay repeats. Range:
0--99
(100 steps in increments of 1)
5.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Short delay effect parameters (parameter type: SHORT DELAY)
For effect type
33
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Delay Time
Adjust the delay time. Range:
0.1--9.9 ms
,
10--99 ms
,
100--200 ms
3.
Feedback
Adjust the number of delay repeats. Range:
0--99
4.
Hi Ratio
Adjust the decay ratio of the high frequencies. Range:
0--10
5.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Doubling effect parameters (parameter type: DOUBLING)
For effect type
34
of the preceding "Effect type" table, the following three parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Lch Delay
Adjust the delay time of the L channel. Range:
0.1--9.9 ms
,
10--99 ms
,
100--200 ms
3.
Rch Delay
Adjust the delay time of the R channel. Range:
0.1--9.9 ms
,
10--99ms
,
100--200 ms
4.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Chorus effect parameters (parameter type: CHORUS)
For effect type
35
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Depth
Adjust the chorus depth. Range:
0--99
3.
Double Time
Adjust the time difference of the doubling effect. Range:
0--99
4.
Double Lvl
Adjust the volume of the doubling effect. Range:
0--99
5.
Filter
Adjust the tone of the delay sound. Range:
L9~L1, OFF, H1~H9
*
L1~L9
= LPF (larger numbers will lower the cutoff frequency)
*
H1~H9
= HPF (larger numbers will raise the cutoff frequency)
Flanger effect parameters (parameter type: FLANGE)
For effect type
36
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Rate
Adjust the speed of modulation. Range:
0.01--2.00 Hz
3.
Depth
Adjust the depth of modulation. Range:
0--99
4.
Mod Delay
Adjust the modulation delay. Range:
0--200
5.
Feedback
Adjust the number of modulation repeats. Range:
0--99
Delay pitch effect parameters (parameter type: DELAY PITCH)
For effect type
38
of the preceding "Effect type" table, the following four parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Pitct
Adjust the amount of pitch shift. Range:
-24--0--+24
*
+/-12
is one octave.
+/-24
is two octaves.
3.
Adjust
Make fine adjustments to the amount of pitch shift. Range:
-50--0--+50
*
+50
is a semitone sharp.
-50
is a semitone flat.
4.
Delay Time
Adjust the delay time until the pitch-shifted sound is heard. Range:
0--500 ms
5.
Feedback
Adjust the number of delay repeats. Range:
0--99
Mono pitch effect parameters (parameter type: MONO PITCH)
For effect type
37
of the preceding "Effect type" table, the following three parameters can be adjusted.
1.
Eff Level
Adjust the effect return level:
0~99
2.
Pitch
Adjust the amount of pitch shift. Range:
-24--0--+24
*
+/-12
is one octave.
+/-24
is two octaves.
3.
Adjust
Make fine adjustments to the amount of pitch shift. Range:
-50--0--+50
*
+50
is a semitone sharp.
-50
is a semitone flat.
4.
Mode
Select the processing method. Range:
1--3