beautypg.com

Instructions for recording with buss record, Recording the h input signal to track 1, Channel selection – Fostex VF-16 User Manual

Page 37: Description of buss record

background image

37

ACCESS

PHANTOM

CH STATUS/CH SEL

1

2

3

4

5

6

7

8

TRACK

9

10

11

12

13

14

15

16

TRACK

A

B

C

D

E

F

G

H

INPUT

ORANGE

CH STATUS

INPUT

RED

REC

GREEN

PLAY

MUTE

EQ/COMP

RECALL

STORE

EFF1/EFF2

HI-G/F/Q

AUX1/AUX2

MID-G/F/Q

PAN

LO-G

FADER

CH VIEW

PRE/POST

PRE/POST

COMP

MUTE

MUTE

EFF1

EFF2

DIRECT RCL

MAP

SCENE

CH PARAM EDIT

EFF EDIT

OFF

CH STATUS/CH SEL

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

MASTER

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

+6

-10

-20

-40

-

-30

0

DISP SEL

REC TRK

END

MARK

DIRECT

CLIPBOARD

CLIPBOARD

BUSS

AUTO RTN

AUTO PUNCH

REC ASSIGN

REC TRK

SOURCE

CH STATUS

AUTO PUNCH

START

PGM SEL

RECORD

P.EDIT

VARI

PITCH

ALIGN SEL

SETUP

SCRUB

A RTN

A PLAY

TIME BASE

SEL

OUT

OUT

LOCATE

LOC MEM

IN

IN

4

1

6

7

3

5

2

UNDO/
REDO

HOLD/

EDIT

STORE

PLAY

STOP

F FWD

REWIND

NEXT

PREV

CLIPBOARD PLAY
L O C AT E A B S 0
LOCATE REC END

FADER

ADJUST

SHIFT

LEVEL

ADJUST

EXIT/NO

ENTER/YES

EJECT

JOG

SHUTTLE

2/10/B

6/14/F

7/15/G

8/16/H

L

R

5/13/E

4/12/D

3/11/C

1/9/A

MON OUT

PHONES

UNBAL

INSERT

BAL

UNBAL

0

10

PHONES

0

10

MON OUT

LINE

MIC

PEAK

LINE

MIC

PEAK

LINE

MIC

PEAK

LINE

MIC

PEAK

LINE

MIC

PEAK

LINE

MIC

PEAK

8/16/H

LINE

MIC

PEAK

TRIM

INPUT

7/15/G

LINE

MIC

PEAK

6/14/F

5/13/E

1/9/A

4/12/D

3/11/C

2/10/B

INSERT

BAL

CLEAR

OPTICAL

DIGITAL

MULTITRACKER

1

8

9

7

5

!

2

4

3

10

10 10

11

12

6

!

Instructions for recording with BUSS RECORD

This section will discuss the basic procedures to REC/PLAY with "BUSS" RECORD, which is another recording option.
With DIRECT RECORD, the track recorded was determined according to the input of channel A to H. However,
with BUSS RECORD, recording is possible regardless of the channel input. It is also possible to record the input
of all 8 channels on 2 tracks with BUSS RECORD. Since the recording process takes place via the mixer, it is pos-
sible to apply equalizer and effect sound to the recording.
Note that BUSS RECORD takes place using the REC exclusive "REC BUSS". This "REC BUSS" consists of 2 channels,
L and R, therefore, a maximum of 2 tracks can be recorded at the same time.

Description of BUSS RECORD

BUSS RECORD takes place by sending signals processed through the mixer to the "REC BUSS" for recording. Therefore,
signals applied with equalization and built-in effect can be recorded (added and recorded). Here, we will use the channel
(ORANGE) with an [INPUT] started with the fader as the source channel. However, channels (GREEN) in which [TRACKS]
are started can also be used as a source channel. Ping-pong recording is possible for the source channel recording with
the [TRACK] started channel (GREEN). Note the following precautions for BUSS recording.

WARNING!

Of the [CH STATUS/CH SEL] key of ch9-16, a channel with an "INPUT" which is lit up ORANGE, cannot output sound
of the tracks corresponding to ch9 to16, so it is not possible to go to the READY state using the [BUSS-REC TRK] key.

WARNING!

Precautions for when selecting a source channel with the [BUSS-SOURCE] key. (when key is flashing in GREEN)
* A channel in which the [CH STATUS/CH SEL] key light is OFF is selectable.
* The channel selected will either have a flashing ORANGE or GREEN [CH STATUS/CH SEL] key.
* The [CH STATUS/CH SEL] key that is flashing RED is a READY channel (track) and cannot be selected.

WARNING!

Precautions when selecting a REC track with the [BUSS-REC TRK] key. (key is flashing RED)
* A channel in which the [CH STATUS/CH SEL] key light is OFF is selectable.
* The channel selected has a flashing RED [CH STATUS/CH SEL] key.
* The [CH STATUS/CH SEL] key that is flashing ORANGE or GREEN is selected as a source channel, therefore, it

cannot be selected.

Recording the H Input Signal to Track 1

Here we will record a sound source connected to input H on track 1 of the recorder. Beforehand, set the ch1 to
16 channel faders, master fader and the [TRIM] for A to H to 0. Connect a headphone or speaker to monitor the
sound.

Channel Selection

1. Connect the sound source to record to [INPUT] jack H.

2. Press the [INPUT SEL] key (ORANGE: Flashing).

3. Press the [CH STATUS/CH SEL] key for ch16 so the key

starts "flashing ORANGE (=INPUT)".

The following display appears, and the signals of input H
will start for channel 16.