Yokogawa EJA130A Instruction Manuals and User Guides
We have 10 Instruction Manuals and User Guides for EJA130A Yokogawa
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 47 |
| Size: | 5.18 MB |
Show table of contents
Document Outline
- CONTENTS
- 1. INTRODUCTION
- 2. HANDLING CAUTION
- 3. ABOUT PROFIBUS PA
- 4. GETTING STARTED
- 5. CONFIGURATION
- 6. CALIBRATION
- 7. IN-PROCESS OPERATION
- 8. DIAGNOSTIC INFORMATION
- 9. GENERAL SPECIFICATIONS
- APPENDIX 1. LIST OF PARAMETERS FOR EACH BLOCK OF THE EJA
- APPENDIX 2. LIST OF DTM MENU
- APPENDIX 3. LIST OF PDM (EDDL) MENU
- REVISION RECORD
| Recognized languages: | English |
|---|---|
| Pages: | 40 |
| Size: | 3.09 MB |
| Recognized languages: | English |
|---|---|
| Pages: | 79 |
| Size: | 1.39 MB |
Show table of contents
Document Outline
- CONTENTS
- 1. INTRODUCTION
- 2. HANDLING CAUTION
- 3. ABOUT FIELDBUS
- 4. GETTING STARTED
- 5. CONFIGURATION
- 6. IN-PROCESS OPERATION
- 7. DEVICE STATUS
- 8. GENERAL SPECIFICATIONS
- APPENDIX 1. LIST OF PARAMETERS FOR EACH BLOCK OF THE EJA
- APPENDIX 2. APPLICATION, SETTING AND CHANGE OF BASIC PARAMETERS
- APPENDIX 3. OPERATION OF EACH PARAMETER IN FAILURE MODE
- APPENDIX 4. PID BLOCK
- A4.1 Function Diagram
- A4.2 Functions of PID Bock
- A4.3 Parameters of PID Block
- A4.4 PID Computation Details
- A4.5 Control Output
- A4.6 Direction of Control Action
- A4.7 Control Action Bypass
- A4.8 Feed-forward
- A4.9 Block Modes
- A4.10 Bumpless Transfer
- A4.11 Setpoint Limiters
- A4.12 External-output Tracking
- A4.13 Measured-value Tracking
- A4.14 Initialization and Manual Fallback (IMan)
- A4.15 Manual Fallback
- A4.16 Auto Fallback
- A4.17 Mode Shedding upon Computer Failure
- A4.18 Alarms
- A4.19 Example of Block Connections
- APPENDIX 5. LINK MASTER FUNCTIONS
- APPENDIX 6. SOFTWARE DOWNLOAD
- A6.1 Benefits of Software Download
- A6.2 Specifications
- A6.3 Preparations for Software Downloading
- A6.4 Flow of Software Download
- A6.5 Download Files
- A6.6 Steps after Activating a Field Device
- A6.7 Troubleshooting
- A6.8 Resource Block’s Parameters Relating to Software Download
- A6.9 View Objects Altered by Software Download
- A6.10 System/Network Management VFD Parameters Relating to Software Download
- A6.11 Comments on System/Network Management VFD Parameters Relating to Software Download
- REVISION RECORD
| Recognized languages: | English |
|---|---|
| Pages: | 31 |
| Size: | 363 KB |
Show table of contents
Document Outline
- CONTENTS
- PRELIMINARY
- 1. ZERO POINT ADJUSTMENT
- 2. HART COMMUNICATOR OPERATION
- 2.1 Conditions of Communication Line
- 2.2 Basic Operation of the HART Communicator (Model 275)
- 2.3 Parameters
- 2.3.1 Parameter Usage and Selection
- 2.3.2 Menu Tree
- 2.3.3 Setting Parameters
- (1) Tag No.
- (2) Unit
- (3) Range Change
- (4) Output Mode (Linear/Sq root)
- (5) Damping Time Constants
- (6) Output Signal Low Cut Mode Setup
- (7) Bi-directional Flow Measurement
- (8) Integral Indicator Display Mode
- (9) Integral Indicator Scale
- (10) Unit for Displayed Temperature
- (11) Unit for Displayed Static Pressure
- (12) Test Output
- (13) Sensor Trim
- (14) Trim Analog Output
- (15) Burst Mode
- (16) Multidrop Mode
- (17) External Switch Mode
- (18) Software Write Protect
- (19) Hardware Write Protect and Burnout Direction(with Optional code /F1)
- (20) H2O Unit Select
- 2.4 Self-Diagnostics
- 3. PARAMETER LISTS
- REVISION RECORD
| Recognized languages: | English |
|---|---|
| Pages: | 6 |
| Size: | 225 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 83 |
| Size: | 3.12 MB |
Show table of contents
Document Outline
- CONTENTS
- 1. INTRODUCTION
- 2. HANDLING CAUTIONS
- 2.1 Model and Specifications Check
- 2.2 Unpacking
- 2.3 Storage
- 2.4 Selecting the Installation Location
- 2.5 Pressure Connection
- 2.6 Waterproofing of Cable Conduit Connections
- 2.7 Restrictions on Use of Radio Transceiver
- 2.8 Insulation Resistance and Dielectric Strength Test
- 2.9 Installation of Explosion Protected Type
- 2.10 EMC Conformity Standards
- 2.11 PED (Pressure Equipment Directive)
- 2.12 Low Voltage Directive
- 3. COMPONENT NAMES
- 4. INSTALLATION
- 5. INSTALLING IMPULSE PIPING
- 6. WIRING
- 7. OPERATION
- 8. BRAIN TERMINAL BT200 OPERATION
- 8.1 BT200 Operation Precautions
- 8.2 BT200 Operating Procedures
- 8.3 Setting Parameters Using the BT200
- 8.3.1 Parameter Summary
- 8.3.2 Parameter Usage and Selection
- 8.3.3 Setting Parameters
- (1) Tag No. Setup
- (2) Calibration Range Setup
- (3) Damping Time Constant Setup
- (4) Output Mode and Integral Indicator Display Mode Setup
- (5) Output Signal Low Cut Mode Setup
- (6) Integral Indicator Scale Setup
- (7) Unit Setup for Displayed Temperature
- (8) Unit Setup for Displayed Static Pressure
- (9) Operation Mode Setup
- (10) Impulse Line Connection Orientation Setup
- (11) Output Status Display/Setup when a CPU Failure
- (12) Output Status Setup when a Hardware Error Occurs
- (13) Bi-directional Flow Measurement Setup
- (14) Range Change while Applying Actual Inputs
- (15) Zero Point Adjustment
- (16) Test Output Setup
- (17) User Memo Fields
- (18) Test Output Setup (K10: OUTPUT X%)
- (19) User Memo Fields (M: MEMO)
- 8.4 Displaying Data Using the BT200
- 8.5 Self-Diagnostics
- 9. MAINTENANCE
- 10. GENERAL SPECIFICATIONS
- Customer Maintenance Parts List
- REVISION RECORD
| Recognized languages: | English |
|---|---|
| Pages: | 4 |
| Size: | 405 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 2 |
| Size: | 17 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 47 |
| Size: | 5.20 MB |
Show table of contents
Document Outline
- CONTENTS
- 1. INTRODUCTION
- 2. HANDLING CAUTION
- 3. ABOUT PROFIBUS PA
- 4. GETTING STARTED
- 5. CONFIGURATION
- 6. CALIBRATION
- 7. IN-PROCESS OPERATION
- 8. DIAGNOSTIC INFORMATION
- 9. GENERAL SPECIFICATIONS
- APPENDIX 1. LIST OF PARAMETERS FOR EACH BLOCK OF THE EJA
- APPENDIX 2. LIST OF DTM MENU
- APPENDIX 3. LIST OF PDM (EDDL) MENU
- REVISION RECORD
| Recognized languages: | English |
|---|---|
| Pages: | 4 |
| Size: | 109 KB |