HP 2500C Series - Manual (Page 83)

Operating Overview 2-25
139 DEFERRED_ERROR_TRAP Error happened during power up but printer recovered Printer error-trapped in a previous lifetime.
141 NVM_ERR_NOT_INIT Not used Attempt to read/write before init.
142 NVM_ERR_GENERIC Not used Non-specific NVM error.
143 NVM_ERR_DEVICE_ABSENT NVM errors Reset printer =>Replace logic PCA Requested memory device did not respond.
144 NVM_ERR_WRITE NVM errors Reset printer =>Replace logic PCA Protocol error on write operation to NVM.
145 NVM_ERR_READ NVM errors Reset printer =>Replace logic PCA Protocol error on read operation to NVM.
146 NVM_ERR_READBACK NVM errors Reset printer =>Replace logic PCA Failed readback/verify after write.
147 NVM_ERR_DATA_NOT_VALID NVM errors Reset printer =>Replace logic PCA Device works OK.
148 NVM_ERR_UNKNOWN_TAG NVM errors Reset printer =>Replace logic PCA Data tag invalid.
149 NVM_ERR_UNKNOWN_FORMAT NVM errors Reset printer =>Replace logic PCA Chip functions but has invalid format.
151 NVM_ERR_BAD_CHIP_TAG Penhead and cartridge errors –Not used Acumen's chip tag unrecognized.
152 NVM_ERR_BAD_FAMILY Penhead and cartridge errors –Not used Acumen's family ID unrecognized.
153 NVM_ERR_BAD_COLOR Penhead and cartridge errors –Not used Acumen's color code did not match device ID.
154 NVM_ERR_TSR_VALUE Penhead and cartridge errors –Not used Acumen TSR value = 0.
155 NVM_ERR_DROP_VALUE Penhead and cartridge errors –Not used Acumen drop volume = 0.
156 NVM_ERR_BAD_TOKEN Penhead and cartridge errors –Not used Token area failed zero-write self test.
157 NVM_ERR_BAD_WRITE_PROT Penhead and cartridge errors –Not used Write-protect area failed self test.
158 NVM_ERR_BAD_MODEL_NUM Penhead and cartridge errors –Not used Acumen Model Number field out of range.
159 NVM_ERR_INCOMPAT_INK Penhead and cartridge errors –Not used Non-approved bit and "JETSERIES".
161 NVM_ERR_BAD_MFG_WEEK Penhead and cartridge errors –Not used Mfg week > 51.
162 NVM_ERR_SPARE Penhead and cartridge errors –Not used Previously was Gas Gauge Gap.
163 NVM_ERR_POOL_ALLOC_FAIL System recources – Reset printer No memory to allocate pool from.
164 NVM_ERR_ACU_BAD_SIZE Penhead and cartridge errors –Not used Token Write-protected or Scratchpad size = 0.
165 NVM_ERR_DUPLICATE_TAG Penhead and cartridge errors –Not used Two identical tags were found in an Acumen chip.
166 NVM_ERR_TOKEN_MISLOC Penhead and cartridge errors –Not used Status superfield not located in token area.
167 NVM_ERR_I2C_CONF_FAIL
Bus used for connecting devices on the PCA experiences error.
Reset Printer => Replace PCA A failure was detected on the serial bus used to access NVM
devices (I2C bus). The following extended error codes apply :
001 = STUCK_LO_SDA
002 = STUCK_HI_SDA
004 = STUCK_LO_SCL
005 = STUCK_LO_SCL + STUCK_LO_SDA
006 = STUCK_LO_SCL + STUCK_HI_SDA
008 = STUCK_HI_SCL
009 = STUCK_HI_SCL + STUCK_LO_SDA
010 = STUCK_HI_SCL + STUCK_HI_SDA
Memory Manager
171 MM_PROC_WAITING Not used Memory Manager error traps.
172 MM_SIGNAL_ERR Not used
173 MM_MAX_WAIT_ERR Not used MM debug = 0.