Sealey TA303 - Manual (Page 2)

TA303 Issue no: 2 - 20/12/11
Original Language Version
3. SPECIFICATION
Range Resolution Accuracy
400.0mV 0.1mV ± 0.5% of reading ± 3 digits
4.000V 1mV
40.00V 10mV ±1.5% of reading ± 2 digits
400.0V 100mV
600V 1V ± 1.8% of reading ± 2 digits
Range Resolution Accuracy
400.0mV 0.1mV ± 1.5% of reading ± 5 digits
4.000V 1mV ± 1.0% of reading ± 3 digits
40.00V 10mV ± 1.5% of reading ± 3 digits
400.0V 100mV
600V 1V ± 2.0% of reading ± 4 digits
DC Voltage (Auto ranging)
AC Voltage (Auto ranging)
Input Impedance: 10MΩ.
Maximum Input: 600Vdc.
Input Impedance: 10MΩ.
Frequency range: 50 to 60Hz.
Maximum Input: 600Vac rms.
Range Resolution Accuracy
4.000kHz 1Hz
40.00kHz 10Hz ± 1.5% of reading ± 3 digits
400.0kHz 100Hz
4.000MHz 1000Hz
40.00MHz 1kHz ± 2.0% of reading ± 4 digits
Frequency (Auto ranging)
Range Resolution Accuracy
0.5%~99.0% 0.1% ± 2.0% of reading ± 5 digits
Duty Cycle
Pulse Width: >100us, <100ms
Sensitivity: > 5V rms
Frequency width: 5Hz - 100kHz
Cylinder Range Resolution Accuracy
4CYL 0~90.0°
5CYL 0~72.0° 0.1° ± 2.0% of reading ± 4 digits
6CYL 0~60.0°
8CYL 0~45.0°
Dwell Angle
Sensitivity: >5V rMS MIn up to 4.0000MHz range.
>15V rMS MIn on 40.00MHz range.
GENERAL INSTRUMENT SPECIFICATION
Instrument complies with IEC 1010-1 En61010-1
Insulation Class 2, Double Insulation
Overvoltage category CAT.III 1000V / CAT.IV 600V
Display 4000 counts LCD display with
function indication
Polarity Automatic, (-) negative polarity indication.
Over range "OL" marks indication
Low battery indication "BAT" is displayed when the battery
voltage drops below the operating level
Measurement rate 2 times per second, nominal
Auto power off Analyser automatically shuts down after
approx. 30 minutes of inactivity
Operating environment 0ºC to 50ºC (32ºF to 122ºF) at < 70%
relative humidity.
Storage temperature -20ºC to 60ºC (-4ºF to 140ºF) at < 80%
relative humidity.
For inside use, max height 2000m
Pollution degree 2
Power One 9V battery (PP3)
Dimensions 170mm x 79mm x 50mm
Weight 366g
FUNCTION RED TERMINAL INPUT LIMIT
DC/AC Volts, Ohms, Continuity, Diode,
CAP., Type-K TEMP., Hz, % Duty,
Ms Dwell, rPM
VΩHz% etc. 600Volts AC DC
Current AC/DC 400mA 400mA 400mA DC/AC
Current AC/DC 20A 20A *20A DC/AC
* 20 Amp measurement for 30 seconds maximum.
 Ohms cannot be measured if voltage is present, ohms can be measured only in a non-powered circuit. However, the analyser is protected to 600 volts.
fig.2.