Legrand MS3650 - Manual (Page 3)

INSTRUCTION / INSTALLATION SHEET
evōQ™ 3000 In-Ceiling and In-Wall
Speakers
IS-0242 Rev. D
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
©Copyright 2006 by On-Q/Legrand All Rights Reserved. Page 3 of 3
B. “Trim-out”
steps:
1. After drywall and/or painting is complete, push the speaker wire
through hole, center template over hole, mark with a pencil and cut
out with a dry-wall knife.
2. Hold the speaker with one hand, (if speaker grill is off, pay careful
attention not to push on the woofer’s cone, this can cause
permanent contortion of the voice coil, thus producing a
mechanical rubbing sound or speaker failure), push in the speaker
terminal connectors and insert wires; remove speaker grill. Be
sure to have the positive wire in the RED terminal and the negative
wire in the BLACK terminal.
NOTE: Wiring both speakers identically as the above instruction
states will yield speakers that are “in phase”. If one speaker is
wired opposite of the other, the speakers will be “out of phase”
with one another. If the speakers are “out of phase” the sound
might appear smeared (canned) and a significant loss of bass
might be noticeable due to phase cancellation. Make sure every
installed speaker is correctly phased.
3 Use one hand to push the speaker into the cut out (again, pay
careful attention not to push on the woofer’s cone, this can cause
permanent contortion of the voice coil, thus producing mechanical
rubbing sound or speaker failure) and the other to turn the screws
that engage the installation tabs (see Figure 5). Tighten the tabs in
a cross or X-pattern until “snug”. Be careful not to over tighten the
tabs or damage could result. The speaker should appear flush to
the surface.
NOTE: If using a cordless drill/screwdriver, it is suggested that
the screws be turned until almost tight, then finish tightening via
a hand screwdriver.
NOTE: A strip of grill adhesive is provided to more securely
attach the speaker grills on final installation. Simply insert several
short strips evenly around the grill slot prior to insalling the grill
cover.
6.5" Speaker (0.7 CuFt) Blocking Distance
16" on Center, 2x4 24.00"
16" on Center, 2x6 15.25"
16" on Center, 2x8 11.50"
16" on Center, 2x10 9.00"
16" on Center, 2x12 7.50"
24" on Center, 2x4 15.50"
24" on Center, 2x6 10.00"
8" Speaker (2.1 CuFt) Blocking Distance
16" on Center, 2x4 71.50"
16" on Center, 2x6 45.50"
16" on Center, 2x8 34.50"
16" on Center, 2x10 27.00"
16" on Center, 2x12 22.25"
24" on Center, 2x4 46.00"
24" on Center, 2x6 29.50"
evōQ™ Speaker Blocking
Chart
Figure 5
evōQ™ 3000 evōQ™ 3000 evōQ™ 3000 evōQ™ 3000
Size/Type 6.5" In-Ceiling 6.5" In-Wall 8" In-Ceiling 8" In-Wall
Efficiency 91dB 91dB 91dB 91dB
Power (RMS/Peak) 50W/100W 50W/100W 75W/150W 75W/150W
Frequency
Response
60-20K 60-20K 50-20K 50-20K
Woofer Type Mica Fiber Mica Fiber Mica Fiber Mica Fiber
Tweeter Type PEI Mylar PEI Mylar PEI Mylar PEI Mylar
Drywall Hole Size 7.75” dia. 7.5” x 10.75” 9.5” dia. 8.75” x 12.75”
Speaker
Specifications