Legrand V2418 User Manual
V2418, External elbow coupling and cover
V2418
External Elbow
Coupling and Cover
Installing the V2418 Coupling and Cover
1. Cut V2400B Base/V2400C Cover sections to the desired length. NOTE: To
ensure proper fit: Raceway Base and Cover must be cut to the same length.
Receptacle cutouts in Cover and mounting holes in Base must match.
2. Locate and mark 0.300" diameter mounting holes in V2400B Raceway Base
that correspond to receptacle spacing on harness.
3. Insert coupling into V2400B Base end and mount first raceway section (Fig. 1
and 2) to wall using No.10 Panhead Screws in unmarked mounting holes.
4. Position next base section onto V2418 coupling, and fasten to wall.
5. Follow steps C and D in Section 2 of V2400 Plugmold
®
Installation
Instructions for proper mounting and wiring procedure.
6. Snap on V2400C Raceway Covers and V2418 Cover over joint in corner.
©1996 The Wiremold Company
39964 896
60 Woodlawn Street
West Hartford, CT 06133-2500
1
2
3
4
- SCRWV (2 pages)
- TM8LOCATORW (2 pages)
- TMHWLLOUVCC (2 pages)
- TM83USBWCC6 (2 pages)
- TD703P (2 pages)
- DRM (2 pages)
- WSLV700W Magnetic Low Voltage Dimmers (2 pages)
- TLV1003W (4 pages)
- PS4100MIR7W (2 pages)
- Wide Slide Series Incandescent Dimmers (2 pages)
- Wide Slide Series Incandescent Dimmers (2 pages)
- WIUFC10W (2 pages)
- WIUC10WL (2 pages)
- SWP262W (2 pages)
- 91583W (4 pages)
- 95181W (4 pages)
- S120JFAN (1 page)
- S120RGAC (4 pages)
- 2300 Series Power-Rated Raceway Round Device Boxes (1 page)
- 4000 Two-Piece Metal Raceway (2 pages)
- 2400BD Divided Steel Raceway Fittings (2 pages)
- 2300 Series Power-Rated Raceway Round Device Boxes (4 pages)
- WSB Series WallSource (4 pages)
- AL5200 Series Large Multi-Channel Aluminum Surface Raceway (4 pages)
- AL5200 Series Large Multi-Channel Aluminum Surface Raceway (2 pages)
- 2300 Series Power-Rated Raceway Round Device Boxes (2 pages)
- 2300 Series Power-Rated Raceway Round Device Boxes (4 pages)
- OR-PHDHJU72 (2 pages)
- TBCRVGA (4 pages)
- BZTPP Series (1 page)
- TS2345AX1L2GYRT Whip-Ended TableSource Work Surface Modules (2 pages)
- 880ADP (1 page)
- TS2345AX1L2GYRT Whip-Ended TableSource Work Surface Modules (2 pages)
- TS2345AX1L2GYRT Whip-Ended TableSource Work Surface Modules (6 pages)
- NM2000 Series Nonmetallic Plugmold Multioutlet System Receptacle Replacement (4 pages)
- 880ADP (2 pages)
- 5450RT Device Mounting Bracket (6 pages)
- 880ADP (4 pages)
- 5450RT Device Mounting Bracket (2 pages)
- BZTPP Series (4 pages)
- K/KP (4 pages)
- K/KP deQuorum Worksurface Flip-Up Portal (2 pages)
- DQFP20UST-2A (4 pages)
- OR-205KAS9EA-09 (76 pages)
- RMS Plug-In Outlet Center Units (4 pages)