Cfn router configurations – Gasboy C01533 User Manual
Page 2
Boca Research
®
is a registered trademark of Boca Research Inc. Gasboy
®
is a registered trademark of Gasboy International. Hayes
®
is a registered trademark
of Hayes Microcomputer Products, Inc. MultiTech
®
is a registered trademark of Multi-Tech Systems, Inc. Practical Peripherals
®
is a registered trademark of
Practical Peripherals, Inc. TopKAT
™
is a trademark of Gasboy International. Zoom
®
is a registered trademark of Zoom Telephonics, Inc.
© 2010 GASBOY
7300 West Friendly Avenue · Post Office Box 22087 · Greensboro, North Carolina 27420 · Phone 1-800-444-5529 ·
· Printed in the U.S.A.
Setup Instructions for C05899 - Credit/Debit Network Modem
Setup Instructions for C05899 - Credit/Debit Network Modem
The C05899 Credit/Debit Card Network Modem is intended for Site Controller II, Site Controller III, or Islander II
with a network interface that requires the fuel management system to contact a credit or debit network for verification
of a user’s card. This modem is identified by the following manufacturers and model numbers:
Manufacturers
Model Numbers
Manufacturers
Model Numbers
Gasboy Quick Connect Network Modem - Multitech
MT2834ZDXb
Boca Research
M024ED
Zoom
2948L, 2949L
MultiTech
MT5656ZDX
Hayes Accura
4703US
Important: The modems that are used for a bank network dial-out require a dedicated phone line.
Configuring for use as a Credit/Debit Card Network Modem
• If the modem is connected to a CFN system, use the disk supplied with the modem to run the configuration utility,
PROGMODM.CMD. Insert the disk into the A: drive and type A:PROGMODM. Follow the instructions in
PROGMODM for configuring as a bank network modem.
• If you do not have the disk containing the PROGMODM.CMD utility, proceed as follows to configure the modem:
Note: The
symbol denotes Enter key and the 0s are zeros, not the letter O.
1
Connect a terminal to the modem with a 1:1 cable male DB-25 to male DB-25 (C04549) or male DB-25 to
female DB-9 (Q13204-09). The terminal must be configured at the baud rate at which the modem will operate.
2
Type AT&F&W . The Gasboy Quick Connect modem will not respond. A confirmation message “OK”
appears in all other modems.
3
Manufacturers
Baud Rate
Type
Modem Response
Gasboy Quick Connect
1200
ATE0Q0V0X4&B1&Q1&D2&E3$MB1200S0=0S6=1S11=60&W
0
2400
ATE0Q0V0X4&B1&Q1&D2&E3$MB2400S0=0S6=1S11=60&W
0
Zoom
1200
ATV0E0X4\N1S0=0S37=5S7=255S11=70&K0%C0&W
0
2400
ATV0E0X4\N1S0=0S37=6S7=255S11=70&K0%C0&W
0
Boca Research
1200
or
2400
ATV0X0E0L1&Q0&D2&C1&S0&W
0
Hayes
1200
or
2400
ATV0X0Q0E0M1S0=0S7=255S9=6&Q6&K0&W
0
MultiTech Model
MT5656ZDX
1200
ATV0E0X4\N1S0=0S7=255S11=70&K0%C0+MS=V22
0
AT&W
0
2400
ATV0E0X4\N1S0=0S7=255S11=70&K0%C0+MS=V22B
0
AT&W
0
Perform the command for the specific modem as listed in the following table:
The modem is now ready for testing. The settings are saved and the configuration is not lost when the power is turned
off.
CFN Router Configurations
Most CFN network routers use a MODEMS.INI file. Earlier versions of MODEMS.INI do not support the MultiTech
modems. Make a backup copy of the existing MODEMS.INI file. If your site controller is running SCII software
V2.3M and earlier, or SCIII 3.3F and earlier, copy the MODEMS2.INI file from the supplied disk to the
MODEMS.INI file in the BIN directory in the site controller. If your site controller is running SCIII 3.4 and later,
copy the MODEMS3.INI file from the supplied disk to the MODEMS.INI file in the BIN directory in the site
controller. After the file is copied, select the new modem from the router configuration menu.
If the router you are using does not use a MODEMS.INI file, do not copy the file from the disk. Choose the correct
modem in the router’s configuration menu. If the correct modem is not listed, choose Hayes 1200 for any of these
modems.