Spectrum Controls 140 MPM 204 00sc - Manual (Page 26)

Quantum Series 140 MPM 204 00sc
28
2. 2. 2. 2. 2. Open ModSoft, and access the I/O map screen.
3. 3. 3. 3. 3. Select the slot in which you have installed the module.
4. 4. 4. 4. 4. Now enter Shift+? to display a list of modules available for placement in the selected slot.
5. 5. 5. 5. 5. Choose your Quantum counter module from the list. For module-specific help, enter Alt+H.
6. 6. 6. 6. 6. Choose the first 3X and 4X registers to be used in the system for the module.
7. 7. 7. 7. 7. Now enter the zoom screens by highlighting the entry for your module and pressing Alt+Z. For zoom
screen operation, see Modicon’s ModSoft Programmer User Manual.
8. 8. 8. 8. 8. Select an input type for each group of two channels. The default is 5 volts.
9. 9. 9. 9. 9. For each group of two channels, select an input range that corresponds to the input type selected. See “
Input Range, Bits 15 and 16. Input Range, Bits 15 and 16. Input Range, Bits 15 and 16. Input Range, Bits 15 and 16. Input Range, Bits 15 and 16. ”
10. 10. 10. 10. 10. Select a gate range for each group of two channels. See “ Gate Range, Bit 13 and 14. Gate Range, Bit 13 and 14. Gate Range, Bit 13 and 14. Gate Range, Bit 13 and 14. Gate Range, Bit 13 and 14. ”
1 1 1 1 11. 1. 1. 1. 1. Select a filter frequency for each channel. See “ 30 kHz Filter 30 kHz Filter 30 kHz Filter 30 kHz Filter 30 kHz Filter, Bit 12. , Bit 12. , Bit 12. , Bit 12. , Bit 12. ”
12. 12. 12. 12. 12. Select a filter frequency for each channel. See “ 15 kHz Filter 15 kHz Filter 15 kHz Filter 15 kHz Filter 15 kHz Filter, Bit 1 , Bit 1 , Bit 1 , Bit 1 , Bit 11. 1. 1. 1. 1. ”
13. 13. 13. 13. 13. Select a count size for each channel. See “ Count Size, Bit 10. Count Size, Bit 10. Count Size, Bit 10. Count Size, Bit 10. Count Size, Bit 10. ”
14. 14. 14. 14. 14. Select signal timeout (for frequency conversion). Timeout should be equal twice the maximum cycle.
For example, if the 0.5Hz is the minimum frequency 1/0.5Hz x 2 = 4 seconds. The timout needs to be
equal to 4 seconds or more. Leaving this register at the default of 0 seconds actually sets the timout to
6 seconds.
Setting Up Concept Setting Up Concept Setting Up Concept Setting Up Concept Setting Up Concept
For Concept to recognize the Quantum counter module, you must update the software with the files
SPECTRUM.MDC and SPECTRUM.HLP. See “
Setting Up the Configuration Software. Setting Up the Configuration Software. Setting Up the Configuration Software. Setting Up the Configuration Software. Setting Up the Configuration Software. ”
To install the runtime files for Concept:
1. Identify the path in which Concept is installed, for example, C:\CONCEPT\. You will probably use the A: drive for the
installation disk.
2. Using your file manager copy the files SPECTRUM.MDC and SPECTRUM.HLP on the disk to the C:\CONCEPT
directory.
3. Verify that the files have been copied to the C:\CONCEPT directory.
Setting Zoom Registers Using Concept Setting Zoom Registers Using Concept Setting Zoom Registers Using Concept Setting Zoom Registers Using Concept Setting Zoom Registers Using Concept
The next procedure describes how to enable the zoom registers and make configuration settings in Concept.
Refer to “
Zoom Register Layout. ”