Spectrum Controls 1769sc-HART Modules - Manual (Page 165)

Chapter 9: Diagnostics and Troubleshooting
User’s Manual 0300217-03 Rev. A
9-5
Section 9.7
Error Codes
The table below explains the extended error code.
Table 9-4 (Extended Fault Codes)
Er r o r T yp e He x Eq u ivale n t M o d u le Er r o r C o d e Ext e n d e d Er r o r
In f o r m at io n C o d e
Er r o r De s cr ip t io n
No e r r or X000 000 0 0000 0000 No er r or
X216 001 0 0001 0110 W atc hdog r es et er r or
X220 001 0 0010 0000 Cr itic al c ode f ailur e
X221 001 0 0010 0001 Failed c alibr ation/c r itic a l EEPROM f ailur e
X401 010 0 0000 0001 Channel 0 Inv alid Ou tput Range
X402 010 0 0000 0010 Channel 1 Inv alid Ou tput Range
X403 010 0 0000 0011 Channel 2 Inv alid Ou tput Range
X404 010 0 0000 0100 Channel 3 Inv alid Ou tput Range
X405 010 0 0000 0101 Channel 0 Inv alid Data For mat
X406 010 0 0000 0110 Channel 1 Inv alid Data For mat
X407 010 0 0000 0111 Channel 2 Inv alid Data For mat
X408 010 0 0000 1000 Channel 3 Inv alid Data For mat
X409 010 0 0000 1001 Channel 0 Inv alid Fault V alu e.
X40A 010 0 0000 1010 Channel 1 Inv alid Fault V alu e.
X40B 010 0 0000 1011 Channel 2 Inv alid Fault V alu e.
X40C 010 0 0000 1100 Channel 3 Inv alid Fault V alu e.
X40D 010 0 0000 1101 Channel 0 Inv alid Idle V alu e.
X40E 010 0 0000 1110 Channel 1 Inv alid Idle V alu e.
X40F 010 0 0000 1111 Channel 2 Inv alid Idle V alu e.
X410 010 0 0001 0000 Channel 3 Inv alid Idle V alu e.
X411 010 0 0001 0001 Channe l 0 Inv alid Clamps .
X412 010 0 0001 0010 Channe l 1 Inv alid Clamps .
X413 010 0 0001 0011 Channe l 2 Inv alid Clamps .
X414 010 0 0001 0100 Channe l 3 Inv alid Clamps .
X415 010 0 0001 0101 Channel 0 Inv alid Ramp Ra te.
X416 010 0 0001 0110 Channel 1 Inv alid Ramp Ra te.
X417 010 0 0001 0111 Channel 2 Inv alid Ramp Ra te.
X418 010 0 0001 1000 Channel 3 Inv alid Ramp Ra te.
X419 010 0 0001 1001 Channel 0 Conf ig w or d 0 Illegal bits s et
X41A 010 0 0001 1010 Channel 1 Conf ig w or d 0 Illegal bits s et
X41B 010 0 0001 1011 Channel 2 Conf ig w or d 0 Illegal bits s et
X41C 010 0 0001 1100 Channel 3 Conf ig w or d 0 Illegal bits s et
X41D 010 0 0001 1101 Channel 0 Conf ig w or d 1 Illegal bits s et
X41E 010 0 0001 1110 Channel 1 Conf ig w or d 1 Illegal bits s et
X41F 010 0 0001 1111 Channel 2 Conf ig w or d 1 Illegal bits s et
X420 010 0 0010 0000 Channel 3 Conf ig w or d 1 Illegal bits s et
X421 010 0 0010 0001 Chann el 0 Illegal HA RT Pas s thr ou gh r ate.
X422 010 0 0010 0010 Chann el 1 Illegal HA RT Pas s thr ou gh r ate.
X423 010 0 0010 0011 Chann el 2 Illegal HA RT Pas s thr ou gh r ate.
X424 010 0 0010 0100 Chann el 3 Illegal HA RT Pas s thr ou gh r ate.
Har dw a r e-
Spec if ic Er r or
Module- Spec if ic
Conf igu r ation
Er r or
Section 9.8
Module
Inhibit Function
Some controllers support the module inhibit function. See your controller manual for
details.
Whenever the 1769sc-OF4IH module is inhibited, the module continues to provide
information about changes at its outputs to the 1769 CompactBus master (for example, a
CompactLogix controller).