Compaq AA-RHGWB-TE - Manual (Page 6)

6.2.2.2 Fabric . . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–6
6.2.2.3 Arbitrated Loop Topology . . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–7
6.3 Example Fibre Channel Configurations Supported by
TruCluster Server . . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–8
6.3.1 Fibre Channel Cluster Configurations for Transparent
Failover Mode . . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–8
6.3.2 Fibre Channel Cluster Configurations for Multiple-Bus
Failover Mode . . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–10
6.4 Zoning and Cascaded Switches . . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–13
6.4.1 Zoning . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–13
6.4.2 Cascaded Switches . . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–14
6.5 Installing and Configuring Fibre Channel Hardware . . .. . .. . .. . 6–15
6.5.1 Installing and Setting Up the Fibre Channel Switch .. . .. . 6–15
6.5.1.1 Installing the Switch . . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–16
6.5.1.2 Managing the Fibre Channel Switches . . .. . . .. . .. . .. . .. . 6–17
6.5.1.2.1 Using the Switch Front Panel . . .. . .. . .. . . .. . .. . .. . .. . 6–17
6.5.1.2.2 Setting the Ethernet IP Address and Subnet Mask
from the Front Panel .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–18
6.5.1.2.3 Setting the DS-DSGGB-AA Ethernet IP Address
and Subnet Mask from a PC or Terminal . . .. . .. . .. .
6–20
6.5.1.2.4 Logging Into the Switch with a Telnet Connection 6–20
6.5.1.2.5 Setting the Switch Name via Telnet Session . .. . .. . 6–21
6.5.2 Installing and Configuring the KGPSA PCI-to-Fibre
Channel Adapter Module . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–22
6.5.2.1 Installing the KGPSA PCI-to-Fibre Channel Adapter
Module . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–22
6.5.2.2 Setting the KGPSA-BC or KGPSA-CA to Run on a
Fabric . . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–23
6.5.2.3 Obtaining the Worldwide Names of KGPSA Adapters 6–25
6.5.3 Setting up the HSG80 Array Controller for Tru64 UNIX
Installation . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–26
6.5.3.1 Obtaining the Worldwide Names of HSG80 Controller 6–31
6.6 Preparing to Install Tru64 UNIX and TruCluster Server on
Fibre Channel Storage . . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–33
6.6.1 Configuring the HSG80 Storagesets . .. . .. . .. . .. . . .. . .. . .. . .. . 6–33
6.6.2 Setting the Device Unit Number . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–40
6.6.3 Setting the bootdef_dev Console Environment Variable .. . 6–46
6.7 Install the Base Operating System .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. . 6–48
6.8 Resetting the bootdef_dev Console Environment Variable . . 6–49
6.9 Determining /dev/disk/dskn to Use for a Cluster Installation . 6–51
6.10 Installing the TruCluster Server Software . .. . .. . .. . . .. . .. . .. . .. . 6–53
6.11 Changing the HSG80 from Transparent to Multiple-Bus
Failover Mode . . . .. . .. . .. . .. . . .. . .. . .. . .. . .. . . .. . .. . .. . .. . . .. . .. . .. . .. .
6–54
vi Contents