Philips COLOR TV - Manual (Page 14)

S etting the R emote C ontrol T o W ork W ith O ther D evices
Direct Access Method
A Tow that you have looked up
1 V
the three-digit Remote Code
Number for your brand of device,
you are ready to follow the four
simple steps below.
Please read through steps 1-4
before beginning.
i BEGIN)
Place the TV/VCR/ACC
Mode Switch in the proper posi­
tion.
<|> Press the VCR RECORD
button on the remote control and
release.
Press the SmartSound button
on the remote within 30 seconds,
then release.
Enter the THREE-DIGIT
REMOTE CODE NUMBER
for your desired device. The
remote is now ready to send
commands to the unit.
Point the remote at the
Device. Press the POWER button
on the remote to turn the unit
ON.
^
I / S mart H elp
Remember, if this doesn’t
i work the first time, repeat steps
using the same remote code number.
After a second try and the remote
does not operate your device, see if
there is another three-digit code num­
ber (pages 34-35) listed for your
device and repeat the steps above
using the new number.
If after repeated attempts the code
number method does not work you
device, tiy the
SEARCH METHOD
on page 33.
VCR
Satellite Receiver
or DBS, etc
Cable Converter
r SWAP SOURCE POSITION FREEZE O o o o
PIP ON/OFF o
__7
U nderstanding the S mart L ock ™ C ontrol (B lock C hannel )
A fter your personal access code
has been set (see previous
page), you are now ready to select
the channels you want to block out
or censor.
t begin !
I«
Press the MENU button on the
remote to show the onscreen menu.
Press the CURSOR UP ^ or
CURSOR DOWN ■ button until
the words SmartLock are highlight­
ed.
Press the CURSOR RIGHT
button to display the
SmartLock Access screen.
Enter the correct access code
number. “XXXX” shows on the
Access Code display as you press
the NUMBERED buttons.
Press the CURSOR UP ^ or
DOWN ■ buttons until the word
BLOCK is highlighted. Press the
CURSOR RIGHT ^ button then
highlight CHANNELS
BLOCKED.
<§> Press the CURSOR RIGHT
button. Three options will be
displayed; CHANNEL, LOCK or
CLEAR ALL.
<|> With CHANNEL highlighted,
use the NUMBERED buttons to
enter the channel number you wish
to block.
<|> Use the CURSOR DOWN ■
button to highlight the word
LOCK, then press the CURSOR
RIGHT ^ button
to select YES
(block) or NO (do not block). The
channel chosen is now blocked from
viewing.
Repeat steps 7 and 8 for any other
channels you wish to block from
viewing.
To clear blocked channels
follow the steps below:
Press the CURSOR DOWN ■ but­
ton until the words CLEAR ALL
are highlighted, then press the
CURSOR RIGHT ^ button.
The screen will read “ALL
UNBLOCKED” for a moment. At
this point ALL the previously
blocked channels will be unblocked.
INPUT
SLEEPTIMER
►
OFF
[SmartLock ► 1
CLOCK ►
CC OFF
SmartLock
ACCESS CODE
SmartLock
ACCESS CODE
X X X X
BLOCK
CHANGE CODE
BLOCKING OPTIONS ^
[CHANNELS BLOCKED
MOVIE RATINGS ^
PARENTAL GUIDELINE ^
CHANNEL 5
[ lock YES[
CLEAR ALL ►
CHANNEL 5 BLOCKED
BY CHANNEL BLOCKING
ENTER CODE TO VIEW
When a blocked channel is viewed, this is what the screen will display. To view the blocked channel, sim­
ply enter the current access code. Note: Once the access code is entered ALL blocked channels will be
viewable until the TV is powered off. Once the set is turned off and then back on the previously blocked
channels will again be blocked.
CHANNEL
LOCK
5
YES
[CLEAR ALL
CHANNEL
LOCK
[ all UNBLOCKED
Note: When the CLEAR
ALL option is selected, the
CHANNEL option will dis­
play ALL.
If at this point if you change
the LOCK option to YES,
ALL channels will be blocked
from viewing.
32 17