Futaba 8FG 2.4GHz - Manual (Page 77)

77 0RGHO0HQX&RPPRQ)XQFWLRQV!
Touch the RTN button to end adjustment and
return to the cursor mode.
1HHGOHKLJKWULPZRUNVDVKLJKWULPEDVHGRQWKHFHQWHU
:RUNVOLNH$7/WULP
Ɣ$FFHOHUDWLRQVHWWLQJ$LUSODQH
7KLV IXQFWLRQ LV XVHG WR DGMXVW WKH QHHGOHHQJLQH ULVH
characteristics during acceleration. This enables an
DFFHOHUDWLRQIXQFWLRQZKLFKWHPSRUDULO\LQFUHDVHVWKHQHHGOH
operation from the throttle stick.
7KLV IXQFWLRQ LV XVHG ZKHQ WKHUH DUH V\PSWRPV RI WKH
PL[WXUH EHLQJ WRR OHDQ RU WRR ULFK ZKLFK ZRXOG EH
generated by sudden throttle stick inputs.
[Acceleration rate setting (RATE)]
$FFHOHUDWLRQ FDQ EH DGMXVWHG IRU DW ERWK KLJK DQG ORZ
settings.
[Damping rate setting (DUMPING)]
7KHUHWXUQWLPHDIWHURSHUDWLRQ'XPSLQJFDQEHVHW
Move the cursor to the rate item you want to
change and touch the RTN button to switch
to the data input mode.
Adjust the rate by scrolling the touch sensor.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end adjustment and
return to the cursor mode.
[Operation point setting (ACT POS)]
7KHRSHUDWLRQSRLQWDWZKLFKWKHDFFHOHUDWLRQVHWWLQJZLOO
RFFXU,IWKLVSRLQWLVH[FHHGHGDFFHOHUDWLRQLVSHUIRUPHG
Move the cursor to the [ACT POS] item and
hold the throttle stick to the position you
want to change and touch the RTN button
for one second.
Note: When using the acceleration funtion,
since the needle stroke is large, adjust your
settings so there is no binding of your linkage.
Ɣ(QJLQHFXWVHWWLQJ
2SHUDWLRQOLQNHGZLWKWKHWKURWWOHKROGIXQFWLRQWKURWWOHFXW
IXQFWLRQDQGLGOHGRZQIXQFWLRQLVSRVVLEOH7KHWKURWWOHFXW
SRVLWLRQFDQEHDGMXVWHGDFFRUGLQJO\6HWLWWRWKHIXOOFORVHG
position.
Move the cursor to the throttle cut or idle
down item and touch the RTN button to
switch to the data input mode.
Adjust the servo position by scrolling the
touch sensor.
,QLWLDOYDOXH7+5&87,'/('2:1
$GMXVWPHQW UDQJH 7+5 &87 a ,'/(
'2:1a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
6HWWLQJPHWKRG
%HIRUHXVLQJWKLVIXQFWLRQDVVLJQWKH>)8(/0,;@IXQFWLRQ
WRDQXQXVHGFKDQQHOLQWKH/LQNDJHPHQX>)81&7,21@
function.
Ɣ$FWLYDWHWKHIXQFWLRQ
1. Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
T o u c h t h e R T N b u t t o n t o a c t i v a t e t h e
function and return to the cursor mode. (ON
is displayed.)
2. Move the cursor to the [MIX] item and touch
the RTN button to switch to the data input
mode.
Select the mixing mode you want to change
by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to change the mode
and return to the cursor mode.
:KHQ>0,;@LVVHOHFWHGDWWKH>0,;@LWHPWKHWKURWWOHFXUYH
setting data becomes the mixing master side data. When
>810,;@LVVHOHFWHGWKHWKURWWOHVWLFNSRVLWLRQEHFRPHVWKH
mixing master.
ƔSRLQWFXUYHVHWWLQJ
1. Move the cursor to the point rate setting item
you want to adjust and touch the RTN button
to switch to the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end adjustment and
return to the cursor mode.
2. Repeat this procedure for each point.
Ɣ1HHGOHKLJKWULPVHWWLQJ
1. Move the cursor to the needle high trim
selection item and access the switch setup
screen by touching the RTN button. Select
the needle high trim lever.
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
2. Move the cursor to the TRIM rate item and
touch the RTN button to switch to the data
input mode.
Adjust the trim rate by scrolling the touch
sensor.
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH