Futaba 8FG 2.4GHz - Manual (Page 51)

51 )XQFWLRQVRI/LQNDJH0HQX!
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Linkage
menu by touching the
RTN button.
MODEL SELECT The Model Selection function performs model addition, selection,
deletion, copy, and model name setting.
This function is used to load the settings of the
GHVLUHGPRGHOLQWRWKH7)*¶VPHPRU\
The settings may be selected from either the
WUDQVPLWWHU¶VLQWHUQDOPHPRU\RUDQ6'FDUG0%
*%5HPHPEHUWKDWXSWRPRGHOPHPRULHVDUH
available in the transmitter.
The name of the model stored in the transmitter and
the SD card may be changed. This can be very useful
to tell different models settings apart. Each model name
FDQEHDVORQJDVFKDUDFWHUVDQGWKHPRGHOQDPH
DOZD\VDSSHDUVLQWKHGLVSOD\VFUHHQ
7KH&RS\IXQFWLRQLVXVHGWRFRS\SDUDPHWHUV
VHWWLQJV HWF IURP RQH PRGHO GDWD LQWR D VHFRQG
memory. It may be used for getting a head-start on
VHWWLQJXSPRGHOVZLWKDOPRVWWKHVDPHVHWWLQJVRQO\
GLIIHUHQFHVQHHGWREHPRGL¿HGLQVWHDGRIHQWHULQJWKH
FRPSOHWHPRGHOIURPVFUDWFK$OVRWKLVIXQFWLRQPD\
be used to make a backup copy of a model setup before
any changes are made.
Model selection
0RGHOGDWDVDYHGRQWKHWUDQVPLWWHUPHPRU\RWKHUWKDQWKH
PRGHOFXUUHQWO\XVHGFDQEHVHOHFWHG0RGHOGDWDVDYHGRQ
the SD card can not be selected directly.
1. After moving the cursor to the desired model
in the model list, touch the RTN button.
2. Move to [SELECT].
3 . T o u c h t h e R T N b u t t o n . A c o n f i r m a t i o n
message is displayed. Touch the RTN button
for one second and selection is complete.
7UDQVPLVVLRQVWRSVDQGWKHQVWDUWVLQWKHVWDWHRIWKHQHZ
model.
Model addition
$QHZPRGHOFDQEHDGGHGWRWKHWUDQVPLWWHUPHPRU\,WFDQ
not be added to the SD card.
1. Move the cursor to [NEW].
2. T o u c h t h e R T N b u t t o n . A c o n f i r m a t i o n
message appears. Touch the RTN button for
one second.
7KHPRGHOW\SHVHWXSVFUHHQDQGIUHTXHQF\VHWXSVFUHHQDUH
DXWRPDWLFDOO\GLVSOD\HG&RQ¿UPRUFKDQJHWKHPRGHOW\SH
and FASST mode.
7UDQVPLVVLRQVWRSVDQGWKHQVWDUWVLQWKHVWDWHRIWKHQHZ
model.
*The added model appears in the model list of the model
select setup screen.
Model deletion
*The model stored in the transmitter memory or an SD card
can be deleted.
*The current model can not be deleted.
1. Move the cursor to the save destination
display ("TX" or "CARD") and touch the RTN
button to switch to the data input mode.
Select the save destination by scrolling the
touch sensor and touch the RTN button.
ŏ 6HOHFW >02'(/ 6(/(&7@ LQ WKH /LQNDJH PHQX
and access the setup screen shown below by
touching the RTN button.
*The display screen is an example. The
screen depends on the model type.
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
(Model list)
Current model