Futaba 8FG 2.4GHz - Manual (Page 103)

103 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
MOTOR [Corresponding model type]: Airplane/glider, general
7KLV IXQFWLRQ OHWV \RX VHW WKH VSHHG ZKHQ WKH
motor of an F5B or other EP glider is started via
DVZLWFK7KHRSHUDWLRQVSHHGFDQEHVHWIRUWZR
UDQJHV VORZ VSHHG IOLJKW DQG KLJK VSHHG IOLJKW
6SHHG 6SHHG 7KLV IXQFWLRQ FDQ DOVR EH
operated as a safety function by programming it to
DVZLWFK
ŏ 7KH ,Q VLGH DQG 2XW VLGH RSHUDWLQJ VSHHGV FDQ
be adjusted independently in 2 ranges (Speed 1/
Speed 2).
ŏ 7KH ERXQGDU\ EHWZHHQ WKH UDQJHV FDQ EH VHW
(From Speed 1 to Speed 2)
ŏ 7KH RSHUDWLRQDO VSHHG FDQ RQO\ EH DFWLYDWHG DW
the initial operation. However, operation can be
repeated by setting the switch to OFF before the
RSHUDWLRQ LV ÀQLVKHG :KHQ \RX ZDQW WR UHVHW RQH
time operation, set the ACT/INH item to [INH] and
then reset it to [ON].
ŏ 7KH PRWRU FKDQQHO LV FRQWUROOHG E\ 6:* *OLGHU
Initial setting) When changing the switch or stick
ZKLFK FRQWUROV WKH PRWRU ÀUVW FKDQJH )XQFWLRQ RI
the Linkage menu.
Note: Initial setting does not assign a motor
channel according to the model type. Prior to
DVVLJQLQJWKHPRWRUFKDQQHOÀQGDQXQXVHG
channel. Then, use the Function menu of the
Linkage menu.
Set [Control] to the switch you want to use
and [Trim] to [--].
Note: When using this function, always check
the initial operation with the propeller
removed.
ŏ 6HOHFW >02725@ DW WKH 0RGHO PHQX
and access the setup screen shown
below by touching the RTN button.
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH
6HWWLQJPHWKRG
Ɣ$FWLYDWHWKHIXQFWLRQ
When using this function, move the cursor to
the [ACT/INH] item and touch the RTN button
to switch to the data input mode. Select the
[ACT] by scrolling the touch sensor and touch
the RTN button.
When selecting the ON/OFF switch, move the
cursor to the switch item and touch the RTN
button to access the selection screen. Select
the switch and set its ON direction. (Always
ON at "--" setting)
)RUDGHVFULSWLRQRIWKHVZLWFKVHOHFWLRQPHWKRGVHHWKH
description at the back of this manual.
Ɣ0RWRURIISRVLWLRQVHWWLQJ
Move the cursor to the [MOTOR OFF] item
and touch the RTN button for one second
when the motor function switch (SG, etc.) is
in the motor OFF position you want to set. The
direction of the motor switch is memorized.
The screen graph display OFF direction also
changes.
Note:
ŏ)LUVWGHFLGHWKHPRWRU2))GLUHFWLRQDQGWKHQ
set the speed. When you want to reset the
motor OFF direction, also reset the speed.
ŏ :H UHFRPPHQG WKDW 0RWRU 2)) EH VHW LQ
combination with F/S.
ŏ 6HW WKH EDVLF RSHUDWLRQ GLUHFWLRQ ZLWK WKH
Reverse function to match the ESC used.
ŏ$OZD\VVHWWKH0RWRU2))SRVLWLRQ