A&D Weighing AD-4406 - Manual (Page 47)

AD-4406 Weighing Indicator Page 45
13.2. 13.2. 13.2. 13.2. Data Data Data Data Format Format Format Format
There are two types of data format set at F-Function F34 and F35.
The initial data format of F34 is shown below.
Header 1 F34, 35 : 9 (Status)
ST
Stable weight data.
US
Unstable weight data.
OL
Overload (Out of range).
HD
Hold weight data (The response of the “RW” and “RW,n” command).
Header 2 F34, 35 : E (Weight type)
GS
or
G
Gross data.
NT
or
N
Net data
TR
or
T
Tare data.
Data F34, 35 : A, B, C, D (Weight data)
The first of the data bits is the polarity, "+" or "-".
When data is zero, the polarity is "+".
8 digits (bits) including the polarity and a decimal point (dot or comma).
In case of "Out of range", the data bits are replaced by spaces except for the decimal
point.
Unit F34, 35 : F (Unit)
In case of CF07=0, the unit length is 2 digits.
In case of CF07=1, the unit length is 3 digits. Depending on the circumstances, an
A&D printer may not work correctly.
13.3. 13.3. 13.3. 13.3. Command Format Command Format Command Format Command Format
Description of Command
When performing a command, the received command or reply data is sent back.
When the received command can not be performed such as the "busy" state, the
code "
I " is sent back. In this case, insert a delay time. Electrical noise may be the
cause of this error.
13.2. Data Format
ᎊᎨᎹᎹᎰᎨᎮᎬ፧ᎹᎬᎻᎼᎹᎵ፧፯፷ᎋᎯ፰ ᎊᎨᎹᎹᎰᎨᎮᎬ፧ᎹᎬᎻᎼᎹᎵ፧፯፷ᎋᎯ፰ ᎊᎨᎹᎹᎰᎨᎮᎬ፧ᎹᎬᎻᎼᎹᎵ፧፯፷ᎋᎯ፰ ᎊᎨᎹᎹᎰᎨᎮᎬ፧ᎹᎬᎻᎼᎹᎵ፧፯፷ᎋᎯ፰
ᎊᎍ፷፽ᎄ፷፳፸፧ ፧ ᎊᎍ፷፽ᎄ፹ ᎊᎍ፷፾ᎄ፷፧ ፧ ፧ ᎊᎍ፷፾ᎄ፸
፹፧ᎫᎰᎮᎰᎻᎺ፧ ፧ ፺፧ᎫᎰᎮᎰᎻᎺ
Header 1 Header 2 Unit
8-digit data Terminator
T S , S G + , 0 0 0 0 0 0 . g k
T S
S U
L O
D H
G
N
T
S G
T N
R T
g
t
g k
g
t
g k
l t
b l
l t
b l
z o
y c
z o
y c
᎚ᎷᎨᎪᎬ፧ᎪᎶᎫᎬ፧፯፹፷Ꭿ፰ ᎚ᎷᎨᎪᎬ፧ᎪᎶᎫᎬ፧፯፹፷Ꭿ፰ ᎚ᎷᎨᎪᎬ፧ᎪᎶᎫᎬ፧፯፹፷Ꭿ፰ ᎚ᎷᎨᎪᎬ፧ᎪᎶᎫᎬ፧፯፹፷Ꭿ፰
᎓ᎰᎵᎬ፧ᎭᎬᎬᎫ፧፯፷ᎈᎯ፰ ᎓ᎰᎵᎬ፧ᎭᎬᎬᎫ፧፯፷ᎈᎯ፰ ᎓ᎰᎵᎬ፧ᎭᎬᎬᎫ፧፯፷ᎈᎯ፰ ᎓ᎰᎵᎬ፧ᎭᎬᎬᎫ፧፯፷ᎈᎯ፰
ᎋᎬᎪᎰᎴᎨᎳ፧ᎷᎶᎰᎵᎻ፧ᎁ
ᎋᎬᎪᎰᎴᎨᎳ፧ᎷᎶᎰᎵᎻ፧ᎁ ᎋᎬᎪᎰᎴᎨᎳ፧ᎷᎶᎰᎵᎻ፧ᎁ ᎋᎬᎪᎰᎴᎨᎳ፧ᎷᎶᎰᎵᎻ፧ᎁ
፧ ᎋᎶᎻ፧፯፹ᎌᎯ፰፧ᎶᎹ
፧ ᎋᎶᎻ፧፯፹ᎌᎯ፰፧ᎶᎹ ፧ ᎋᎶᎻ፧፯፹ᎌᎯ፰፧ᎶᎹ ፧ ᎋᎶᎻ፧፯፹ᎌᎯ፰፧ᎶᎹ
፧ ᎊᎶᎴᎴᎨ፧፯፹ᎊᎯ፰
፧ ᎊᎶᎴᎴᎨ፧፯፹ᎊᎯ፰ ፧ ᎊᎶᎴᎴᎨ፧፯፹ᎊᎯ፰ ፧ ᎊᎶᎴᎴᎨ፧፯፹ᎊᎯ፰