KEYENCE SJ-F036 - Manual (Page 2)

2
■ Installation Precautions
Avoid installing the SJ-F031/036 in the following locations as this may cause
accidents.
• Locations directly subject to vibration and shock
• Locations subject to ambient temperature out of the 0°C to +50°C range
• Locations subject to ambient humidity out of the 35 to 65%RH range
(condensation not allowed)
• Locations subject to sudden changes in temperature
• Locations subject directly from blasts from air conditioners
• Locations subject to volatile or flammable substance, solvents or corrosive
gases
• Locations subject to large amounts of dirt, and dust, salt, iron and oil smoke
• Locations that may be splashed with water, oil or chemical mist
• Locations where strong magnetic and electrical fields are generated
■ About Warming Up the SJ-F031/036
Leave the SJ-F031/036 for about 20 minutes after turning the power on.
Otherwise, the ion balance may not be stable.
■ Other Precautions
• Be sure to read the WARNINGS and CAUTIONS described in each of the
items in this Instruction Manual.
• The Static Elimination Blower has a built-in EEPROM. Do not turn the Static
Elimination Blower OFF during the setup.
Refer to the following diagram when installing the SJ-F031/036.
• Install the Static Elimination Blower away from the wall or surrounding
objects.
• Install the Static Elimination Blower so that the Electrode Unit can be
removed for replacement.
CAUTION
Note
CAUTION
CAUTION
50 mm or more
50 mm or more
Precautions on Regulations and Standards
■ CE Marking
Keyence Corporation has confirmed that this product complies with the essential requirements of the
applicable EC Directive, based on the following specifications.
Be sure to consider the following specifications when using this product in the Member State of
European Union.
● EMC Directive(2004/108/EC)
• Applicable standard EN61326-1
• Be sure to provide a ground when installing the SJ-F031/036.
• The length of cable (power lead and I/O leads) must be less than or equal to 30m.
Remarks:
These specifications do not give any guarantee that the end-product with this product incorporated
complies with the essential requirements of EMC Directive. The manufacturer of the end-product is
solely responsible for the compliance on the end-product itself according to EMC Directive.
● Low-Voltage Directive (2006/95/EC)
• Applicable Standard : EN61010-1
• Overvoltage category I
• Use this product under pollution degree 2.
• Use the power supply for the SJ-F031/036, that satisfies the requirements of the Limited
Power Source specifications stipulated in EN60950-1 and certified by European third-party certification
organization, or a Keyence Corporation AC adapter (SJ-U2). The specifications of the AC adapter (SJ-
U2) are as follows.
When connecting to an SJ-U2, be sure to use a power cable compliant with European standards.
Applicable standard: EN60950-1
Overvoltage category II
Pollution degree 2
• Be sure to provide a ground when installing the SJ-F031/036.
1ABOUT THE STATIC ELIMINATION BLOWER UNIT SJ-F031/036
1-1 System Configuration
This section describes the system configuration of the Static Elimination Blower SJ-F031/036.
System Configuration
* One of the AC and DC power supplies is used.
START /STOP BALANCE ION FAN
COND IONLEVEL
1 1 1
I/O, DC power supply
AC adapter
I/O cable
to AC power
1-2 Checking the Contents of the Package
The package contains the following components and accessories. Before getting started, make sure
that the package contains everything that it is supposed to contain.
Package Contents
Options
Mounting fixture (OP-84374)
Accessory: M4 screw for fixing the Static
Elimination Blower x 4
Ceiling-mounting fixtures (OP-78477)
Accessory: M4 screw for fixing the Static
Elimination Blower x 4
Electrode Unit for exchanging
(OP-51407) AC adapter (SJ-U2) I/O cable (SJ-FC5)
START /STOP BALANCE ION FAN
COND IONLEVEL
• Instruction Manual • Ground lead
• Warning label (Japanese, German, French, Italian,
Chinese: SC)
* Use as necessary.
SJ-F 031/036
High-speed, High-precision
Built-in-Controller Type Static
Elimination Blower
Instruction Manual