KEYENCE LK-HA100 - Manual (Page 2)

Connecting the head expansion unit
CAUTION
Turn off the power of the LK-HA100 before connecting the head expansion unit.
Otherwise, you may suffer a shock or damage the unit.
1
Connect the head expansion
unit by aligning its
connector to the connector
on the left side of the
controller.
You need to remove the sticker
attached to the left side of the
controller beforehand.
2
Secure the head expansion
unit by tightening the two
fixing screws.
Tightening torque
Limit the tightening torque to
0.7 Nm or less.
3
In the Environment settings,
specify the active head count
and active OUT count.
See "LK-G5000 Series User’s
Manual".
(1) KEYENCE warrants the Products to be free of defects in materials and
workmanship for a period of one (1) year from the date of shipment. If any
models or samples were shown to Buyer, such models or samples were used
merely to illustrate the general type and quality of the Products and not to
represent that the Products would necessarily conform to said models or
samples. Any Products found to be defective must be shipped to KEYENCE
with all shipping costs paid by Buyer or offered to KEYENCE for inspection and
examination. Upon examination by KEYENCE, KEYENCE, at its sole option, will
refund the purchase price of, or repair or replace at no charge any Products
found to be defective. This warranty does not apply to any defects resulting
from any action of Buyer, including but not limited to improper installation,
improper interfacing, improper repair, unauthorized modification,
misapplication and mishandling, such as exposure to excessive current, heat,
coldness, moisture, vibration or outdoors air. Components which wear are not
warranted.
(2) KEYENCE is pleased to offer suggestions on the use of its various Products.
They are only suggestions, and it is Buyer's responsibility to ascertain the
fitness of the Products for Buyer's intended use. KEYENCE will not be
responsible for any damages that may result from the use of the Products.
(3) The Products and any samples (Products/Samples) supplied to Buyer are not
to be used internally in humans, for human transportation, as safety devices or
fail-safe systems, unless their written specifications state otherwise. Should any
Products/Samples be used in such a manner or misused in any way, KEYENCE
assumes no responsibility, and additionally Buyer will indemnify KEYENCE and
hold KEYENCE harmless from any liability or damage whatsoever arising out of
any misuse of the Products/Samples.
(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE
PROVIDED WITH NO OTHER WARRANTIES WHATSOEVER. ALL EXPRESS,
IMPLIED, AND STATUTORY WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF PROPRIETARY
RIGHTS, ARE EXPRESSLY DISCLAIMED. IN NO EVENT SHALL KEYENCE AND
ITS AFFILIATED ENTITIES BE LIABLE TO ANY PERSON OR ENTITY FOR ANY
DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL
DAMAGES (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING
FROM LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF INFORMATION,
LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS OF SAVINGS,
THE COST OF PROCUREMENT OF SUBSTITUTED GOODS, SERVICES OR
TECHNOLOGIES, OR FOR ANY MATTER ARISING OUT OF OR IN
CONNECTION WITH THE USE OR INABILITY TO USE THE PRODUCTS, EVEN
IF KEYENCE OR ONE OF ITS AFFILIATED ENTITIES WAS ADVISED OF A
POSSIBLE THIRD PARTY’S CLAIM FOR DAMAGES OR ANY OTHER CLAIM
AGAINST BUYER. In some jurisdictions, some of the foregoing warranty
disclaimers or damage limitations may not apply.
BUYER'S TRANSFER OBLIGATIONS: If the Products/Samples purchased by
Buyer are to be resold or delivered to a third party, Buyer must provide such
third party with a copy of this document, all specifications, manuals, catalogs,
leaflets and written information provided to Buyer pertaining to the Products/
Samples.
When you change the active head count or active OUT count in the
Environment settings, all the settings of the LK-HA100 except for the
Environment settings are reset. When you connect the LK-HA100 head
expansion unit(s) and add a sensor head(s), be sure to set the active head
count and active OUT count before changing the other measurement settings.
Dimensions
1
2
3
4
5
6
7
8
9
10
11 12 13
14 15 16
17 18 19
20 2
21 22 23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
LAS ER O N
ETH ER NET
USB
DIS PL AY
RS-232 C
HEA D
1 OUT (V) OUT (A) OUT 0V OU T(V) OU T(A) OUT 0V
COM IN
ZER O 1
TIMING 1 GO
LASER 1
DC 24V 1
HEA D
LK- G5 000
2
PO WE R ST AB ILIT Y BR IG HT DA RK
HEAD
(V)
(A)
(A)
LK-HA 100
Connector
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
2
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40 LAS ER ON
ETH ER NET
USB
DIS PL AY
RS-232C
HEAD
1 OUT (V) OUT (A) OUT 0V OUT (V) OUT (A) OUT 0V
COM IN
ZER O 1
TIMING 1 GO
LASER 1
DC 24V 1
HEAD
LK- G5 000
2
PO WE R STA BILIT Y BR IG HT DA RK
HEAD
(V)
(A)
(A)
LK-H A1 00
Screw position
Screw position
NOTE
26.3
124
6
(65) 105.5
35.9
62.1
13.5 14
114
13.5
(65) 128 26.3
124
6
M4
Depth: 6
M4
Depth: 6
DIN rail
WARRANTIES AND DISCLAIMERS
Specifications are subject to change without notice.
KEYENCE CORPORATION
1-3-14, Higashi-Nakajima, Higashi-Yodogawa-ku,
Osaka, 533-8555, Japan
PHONE: +81-6-6379-2211
Copyright (c) 2009 KEYENCE CORPORATION. All rights reserved.
00569E 0049-1 96M00569 Printed in Japan
A6WW1-MAN-0019
CANADA
Phone: +1-905-696-9970
CHINA
Phone: +86-21-68757500
CZECH REPUBLIC
Phone: +420 222 191 483
GERMANY
Phone: +49-6102-36 89-0
FRANCE
Phone: +33 1 56 37 78 00
AUSTRIA
Phone: +43-2236-378266-0
HONG KONG
Phone: +852-3104-1010
BELGIUM
Phone: +32 2 716 40 63 ITALY
Phone: +39-2-6688220
JAPAN
Phone: +81-6-6379-2211
KOREA
Phone: +82-31-642-1270
MEXICO
Phone: +52-81-8220-7900
MALAYSIA
Phone: +60-3-2092-2211
NETHERLANDS
Phone: +31 40 20 66 100
HUNGARY
Phone: +36 14 748 313
POLAND
Phone: +48 71 36861 60
SINGAPORE
Phone: +65-6392-1011
SLOVAKIA
Phone: +421 2 5939 6461
SWITZERLAND
Phone: +41 43 455 77 30
THAILAND
Phone: +66-2-369-2777
TAIWAN
Phone: +886-2-2718-8700
UK & IRELAND
Phone: +44-1908-696900
USA
Phone: +1-201-930-0100