COP-USA CD66MK-HW - Manual (Page 11)

- 8 -
AMOUNT: to select the value of the EXPOSURE COMPENSATION: -7～+7.
RETURN: return to the previous menu.
2.5 MOTION SETUP: enter the submenu of the dome enhancement functions.
PRESETS: enter the submenu to edit the label of the PRESETS.
PRESET NO: to select the preset number, from 1 to 128.
Pic.freeze: PIC.FREEZE setting ON/OFF.(Only some series of camera
support the setting of pic.freeze).
EDIT LABEL: to edit the label of the presets, then the screen will
display the figure as the right. The first line means it is the No. 1 preset,
and the second line is just show “NO LABEL” at the beginning. Now
we can use the joystick or the direction keys to modify the label, turn
left/right to move the cursor, and up/down to change the character, the
press “CLOSE” to save and quit the editing status. It is maximum 10
characters in the label, the characters could be 0
～9, A～Z, blank and
some special characters: “
；：〈 = 〉？，@\+、-./ ］”.
CLR LABAL: to clear the label of the preset.
RETURN: return to the previous menu.
AUTO SCAN: enter the submenu of the AUTO SCAN.
SCAN NO: to select the number of the line scanning: 1～3.
SPEED: the select the level of scanning speed to each line: 1～7.
SET START LIMIT: to set the start point of the scanning line by
joystick or direction keys, then press “CLOSE” to save and return.
SET END LIMIT: to set the end point of the scanning line by joystick or
direction keys, then press “CLOSE” to save and return.
RUN SCAN: to run the scanning line, and if the start point and the end
point are the same one, the dome will scan for 360
°. Press “CLOSE” to
quit.
CLEAR SCAN: to clear the scanning line we selected.
RETURN: return to the previous menu.
PRESET NO. : 001
LABEL: NO LABEL
1. SCAN NO : 001
2. SPEED : 001
3. SET START LIMIT
4. SET END LIMIT
5. RUN SCAN
6. CLEAR SCAN
7. RETURN
AUTO SCAN
1.< PRESETS >
2.
＜ ＜ ＜ ＜ AUTO SCAN ＞ ＞ ＞ ＞
3. ＜ ＜ ＜ ＜ PATROLS ＞ ＞ ＞ ＞
4. ＜ ＜ ＜ ＜ PATTERNS ＞ ＞ ＞ ＞
5. ＜ ＜ ＜ ＜ ＞ ＞ ＞ ＞
MOTION SETUP
6.
CLEAR
7.
EDIT DOME LABEL
RETURN
1.< PRESETS >
2.
＜ ＜ ＜ ＜AUTO SCAN＞ ＞ ＞ ＞
3. ＜ ＜ ＜ ＜PATROLS＞ ＞ ＞ ＞
4. ＜ ＜ ＜ ＜PATTERNS＞ ＞ ＞ ＞
5.
MOTION SETUP
6.
＜ ＜ ＜ ＜CLEAR＞ ＞ ＞ ＞
7.
EDIT DOME LABEL
RETURN
1. PATROL NO : 001
2. EDIT PATROL
3. RUN PATROL
4. CLEAR PATROL
5. RETURN
PATROLS
1. PRESET NO 01
3. EDIT LABEL
5. CLR LABEL
6. RETURN
1.< PRESETS >
2.
＜ ＜ ＜ ＜ AUTO SCAN ＞ ＞ ＞ ＞
3. ＜ ＜ ＜ ＜ PATROLS ＞ ＞ ＞ ＞
4. ＜ ＜ ＜ ＜ PATTERNS ＞ ＞ ＞ ＞
5.
PRESETS
MOTION SETUP
6
＜ ＜ ＜ ＜ CLEAR ＞ ＞ ＞ ＞
7
. EDIT DOME LABEL
. RETURN
2. PIC.FREEZE:ON