Panasonic OMNIVISION PV-S4670 - Manual (Page 20)

Timer Recording
Your VCR can be set up to do a recording
while you are away or otherwise occupied.
Up to 8 programs can be placed in
memory. You can choose to record one
time, daily, or weekly.
L^S^iheck list before you begin.
n All connections are made.
(See pages 6-9.)
□ TV and VCR are plugged in and turned on.
CH VCR/TV selector is set to “VCR.”
n Clock is set to correct time.
□ Record tab in place. (See page 5.)
POWER Multi Function
Display
STOP
VCR -
POWER
CLEAR
PROG
(D
vcn-TV
O O O
ZEWyiUN dOW PAUSE
O © ® @
Q
SZSt VCL CH
?G0
CD
9
II
tHSn AY VCR Pw Pl^
SELECT
1
:o
0 0
f 1 ■
3 3 '
CD Cpcp
cb CDCD
7
i
e
CD CD CD
e APOM.T
CD CD 0
0!
SPjJuZEH
5AF?i-Fi
©
STOP
■WHEEL
k
Important notes when
using a DSS receiver.
• When recording programs via a
DSS receiver the DSS receiver
must be left on.
• When recording programs via an
antenna or cable, the DSS
receiver must be turned off.
o
PROG
Push PROG to display
the program screen.
• If a program is already in
memory, use the Wheel to
select an unused program
number.
START STOP CH
SLP
BY ROTATING WHEEL
:PUSH VflHEEL->
TO END PUSH PROG KEY
Rotate and push the
WHEEL to select and
set the DATE.
Today's Date
WEEKLY(SAT;< 7 —► a- 9 -— 31 ->^
Example i
W Selection Order 1
-WIY----------- 6........... ‘
Daily and Weekly Timer Recording
If you want the program to be recorded
daily (Mon thru Fri) , enter DAILY in
place of the DATE in step 2. If you
want the recording to be on a weekly
basis, enter WEEKLY MON, TUE, etc..
9^TfTsTART STOP C h ]
l(tClNlF>tl
TO END POSr
14TPI ^ START STOP
M i O n I_ [ \ ................................. SLP
BY ROTATING WHEEL
Rotate and push
the WHEEL to select
and set remaining
items at right.
Remaining Items
to be set:
• START time
• STOP time
• CH(annel) number, or LINE
for outside source recording.
• Speed (SP, LP, SLP).
To Make Corrections
Repeatedly push the Wheel to move forward, or the CLEAR button
to move back to the desired item.
Push the WHEEL when program is completed.
“PROGRAM COMPLETED" will appear on-screen.
• if “PROGRAM IS COMPLETE” appears on-screen,
check all entries and make necessary corrections.
• If you enter a channel number
of 100-125, the screen at right
appears a few seconds later.
Rotate and push the
WHEEL to select “DSS”
or “CABLE."
------------ -
IS IT CABLE CHANNEL
OR DSS RECEIVER CHANNEL?
CABLE
SELECT : ROTATE WHEEL
SET ; PUSH WHEEL
PROG
Push PROG to end
the program.
• If you want to enter more
programs, select a blank
program number with Wheel
and repeat steps 2 and 3.
P DT STRAT STOP CH SPD
SELECT 1-8:ROTATE WHEEL
ENTER :PUSH WHEEL
CANCEL :PUSH CLEAR KEY
END :PUSH PROG KEY
o
PROG
Push PROG to exit
this mode.
VCR
O
Push VCR POWER
off to set the timer.
-HESI!-
Multi Function
Display
When recording programs via a cable box, make sure the
cable box is left on. If the cable box cannot be controlled
with the VCR, you must manually select the desired channel.
20
If a DSS channel is selected, the channel will appear as blue numbers on white background.
If the cassette record tab is missing at the time the VCR power is turned OFF, the tape ejects and
the TIMER indicator flashes in the Multi Function Display.
If the start times of two programs overlap, the lower numbered program will have priority.
If the start time for a timer recording comes up during a normal recording or One Tobch Recording (page 19),
the timer recording will not be performed.
If "PROGRAM IS INCOMPLETE" appears on-screen in step 4, check all entries and make necessary corrections