FBT DLM26 - Manual (Page 50)

 Menu “Output 1/2/3/4/5/6” Output Channels Editing in “ Custom ” mode
[access by pushing the “1/2/3/4/5/6” buttons]
When operating in Custom mode, depending from the chosen mode, a couple of Odd and Even
Outputs (as Ch1/Ch2 or/and Ch3/Ch4 or/and Ch5/Ch6) are “coupled” so to get a single “Full
Band” MONO output on the Odd channel of the couple, and for this output a 2 bands Rms
compressor and Peak Limiter is available.
The available configurations in Custom Mode are the following:
3 DCL........... where 3 Outputs are available (Ch1/Ch3/Ch5), each one “Full Band” and
performing a 2 bands Rms Compressor and Peak Limiter, where the splitting frequency of the 2
bands can be custom selected:
− Outputs 1 [5 Bands Eq +2Bands Rms Compressor + 2 bands Peak Limiter]
− Outputs 3 [5 Bands Eq +2Bands Rms Compressor + 2 bands Peak Limiter]
− Outputs 5 [5 Bands Eq +2Bands Rms Compressor + 2 bands Peak Limiter]
− Outputs 2/4/6 [Muted]
2x2 DCL......... where 2 of the available Outputs (Ch1/Ch3) are each one “Full Band” and
performing a 2 bands Rms Compressor and Peak Limiter, where the splitting frequency of the 2
bands can be custom selected.
The Outputs of the Channels 5/6 are performing as in Standard Mode:
− Outputs 1 [5 Bands Eq +2Bands Rms Compressor + 2 bands Peak Limiter]
− Outputs 3 [5 Bands Eq +2Bands Rms Compressor + 2 bands Peak Limiter]
− Outputs 5/6 [ 5 Bands Eq +Rms Compressor + Peak Limiter]
− Outputs 2/4 [Muted]
4+1 DCL......... where 1 of the available Outputs (Ch1) is “Full Band” and performing a 2
bands Rms Compressor and Peak Limiter, where the splitting frequency of the 2 bands can be
custom selected.
The Outputs of the Channels 3/4/5/6 are performing as in Standard Mode:
− Outputs 1 [5 Bands Eq +2Bands Rms Compressor + 2 bands Peak Limiter]
− Outputs 3/4/5/6 [ 5 Bands Eq +Rms Compressor + Peak Limiter]
− Outputs 2 [Muted]
From the “Default Screen”, it is possible to access the Standard “Output Channels” menu by
pressing the “1” or “2” or “3” or “4” or “5” or “6” button (depending from the selected operative
mode). Once pressed, the related blue “EDIT” LED will turn ON.
The Sub-Menus pages can now be scrolled through by rotating clockwise and counter-clockwise
the “NAV/Param.1” encoder.
For parameter editing it is necessary to press ENTER and an arrow will appear on the left of the
screen “->”. Then use the “Param.2” and “Param.3” encoders for selecting and setting the
parameter values. On some parameters that have three independent values, you will also need to
use the NAV/Param.1 encoder, for example for the filter’s parameter setting.
Note: All parameter editing can be done using the “NAV/Param.1”, “Param.2”, and “Param.3”
encoders and the current shown value of the selected option is AUTOMATICALLY loaded during the
encoders' use and stored as the current value once leaving the page.
The channels working in Standard mode, are featuring exactly as described in the previous
session dedicated to the Standard mode.