Dell PowerEdge 800 User Manual
Page 22
Message
Causes
Corrective Actions
Amount of available memory limited to
256MB!
OS Install Mode is enabled
in the System Setup program.
Disable OS Install Mode in the System Setup program. See "Using the System
Setup Program" in your User's Guide.
Attempting to update Remote
Configuration. Please wait....
Remote Configuration is in
progress.
Wait until the process is complete.
BIOS Update Attempt Failed
BIOS remote update failed.
Retry update.
Caution! NVRAM_CLR jumper is installed
on system board.
NVRAM_CLR jumper is
installed.
Remove the NVRAM_CLR jumper. See
Figure A
-2
for the jumper location.
CD-ROM drive not found
Improperly connected or
missing optical drive.
If no optical drive is installed, disable the IDE controller. See "Using the System
Setup Program" in your User's Guide.
If an optical drive is installed, see "
Troubleshooting an Optical Drive
" in
"Troubleshooting Your System."
Decreasing available memory
Faulty or improperly installed
memory modules.
Ensure that all memory modules are properly installed. See "
Troubleshooting
System Memory
" in "Troubleshooting Your System."
Diskette drive 0 seek failure
Incorrect configuration
settings in System Setup
program.
Run the System Setup program to correct the settings. See "Using the System
Setup Program" in your User's Guide.
Faulty or improperly installed
diskette, loose diskette drive
or optical drive interface
cable, or loose power cable.
Replace the diskette. Ensure that the diskette drive and optical drive cables
are properly connected. See "
Troubleshooting a Diskette Drive
" and
"
Troubleshooting an Optical Drive
" in "Troubleshooting Your System."
Diskette read failure
Faulty or improperly inserted
diskette.
Replace the diskette.
Diskette subsystem reset failed
Faulty diskette drive or
optical drive controller.
Ensure that the diskette drive and optical drive cables are properly connected.
See "
Troubleshooting a Diskette Drive
" and "
Troubleshooting an Optical Drive
"
in "Troubleshooting Your System." If the problem persists, see "
Getting Help
."
Drive not ready
Diskette missing or
improperly inserted in
diskette drive.
Reinsert or replace the diskette.
Dual rank DIMMs are not supported in the
following memory sockets in this memory
configuration.
Invalid memory configuration. Correct the memory configuration. See "
General Memory Module Installation
Guidelines
" in "Installing System Components."
Error: Incorrect memory configuration.
Ensure memory in slots DIMM1_A and
DIMM1_B, DIMM2_A and DIMM2_B match
identically in size, speed, and rank.
An unmatched pair of memory
modules is installed.
Install a matched pair of memory modules, or remove the memory module in
socket DIMM1_B. See "
General Memory Module Installation Guidelines
" in
"Installing System Components."
Error: Remote Access Card initialization
failure.
Faulty or improperly installed
RAC.
Ensure that the RAC is properly installed. See "
Troubleshooting Expansion
Cards
" in "Troubleshooting Your System," or "
Installing a RAC Card
" in
"Installing System Components."
Error 8602: Auxiliary device failure.
Verify that the keyboard and mouse are
securely attached to correct connectors.
Loose or improperly
connected mouse or
keyboard cable; faulty mouse
or keyboard.
Replace the mouse. If the problem persists, replace the keyboard.
Gate A20 failure
Faulty keyboard controller
(faulty system board).
See "
Getting Help
."
General failure
Operating system corrupted
or improperly installed.
Reinstall the operating system.
IDE Primary drive 1 not found
Improperly connected or
missing optical drive or tape
backup unit.
Ensure that the drive cables are properly connected. See "
Troubleshooting
Your System
" for the appropriate drive installed in your system.
If no drive is installed, disable the IDE controller. See "Using the System Setup
Program" in your User's Guide.
Keyboard controller failure
Faulty keyboard controller
(faulty system board).
See "
Getting Help
"
Keyboard data line failure
Keyboard failure
Keyboard stuck key failure
Loose or improperly
connected keyboard cable;
faulty keyboard; faulty
keyboard controller.
Ensure that the keyboard is properly connected. If the problem persists,
replace the keyboard. If the problem persists, see "
Getting Help
."
Keyboard fuse has failed.
Keyboard fuse has failed.
Replace the keyboard.
Faulty system board. See "
Getting Help
."
Manufacturing mode detected
System is incorrectly
configured.
After the message appears during system boot, press
manufacturing mode.
Memory address line failure at address,
read value expecting value
Memory double word logic failure at
address, read value expecting value
Memory odd/even logic failure at start
address to end address
Memory write/read failure at address,
read value expecting value
Faulty or improperly installed
memory modules, or faulty
system board.
Ensure that all memory modules are properly installed. See "
Troubleshooting
System Memory
" in "Troubleshooting Your System." If the problem persists, see
"
Getting Help
."
Memory tests terminated by keystroke
The spacebar was pressed
Information only.