Great Plains V300 Assembly Instructions - Manual (Page 11)

Great Plains Mfg., Inc.
Installation Instructions 11
11/08/2006 148-771M
Refer to Figure 17, shown exploded for clarity.
80. Select two each:
(31) 802-551C, HHCS 1/4-20X2 1/4 GR5,
(39) 804-075C, WASHER FLAT 1/4 USS PLT,
(36) 804-006C, WASHER LOCK SPRING 1/4 PLT,
(32) 803-006C, NUT HEX 1/4-20 PLT.
Insert the bolt (31) through the valve (44), and then
the mount (23) plate holes
➀
. Loosely fit a flat
washer (39), lock washer (36) and nut (32).
81. Select two each:
(31) 802-551C, HHCS 1/4-20X2 1/4 GR5,
(39) 804-075C, WASHER FLAT 1/4 USS PLT,
(36) 804-006C, WASHER LOCK SPRING 1/4 PLT,
(32) 803-006C, NUT HEX 1/4-20 PLT.
Insert the bolt out through the mount (23) holes
➁
,
into the shuttle valve notches (45). Loosely fit a flat
washer (39), lock washer (36) and nut (32).
82. Select two each:
(31) 802-551C, HHCS 1/4-20X2 1/4 GR5,
(36) 804-006C, WASHER LOCK SPRING 1/4 PLT,
(32) 803-006C, NUT HEX 1/4-20 PLT,
and four each:
(39) 804-075C, WASHER FLAT 1/4 USS PLT,
From inside the mount (23), place a washer (39) on
each bolt (31), down through the plate hole
➂
into
the check valve notches (47). Loosely fit another
flat washer (39), lock washer (36) and nut (32).
83. Snug the valve assembly (44)(45)(47) against the
mounting plate (23), seat all bolts deeply in
notches, and tighten all bolts and nuts.
Refer to Figure 18
84. Select two each:
(28) 802-024C, HHCS 3/8-16X3 GR5,
(37) 804-013C, WASHER LOCK SPRING 3/8 PLT
(33) 803-014C, NUT HEX 3/8-16 PLT
Select also six:
(40) 804-087C, WASHER FLAT 3/8 HARD
ASTMF436
From the Left outside of the mount, insert each bolt
(28) through one washer (40), then through the
plate holes
➃
. Slide two additional washers (40) as
spacers, then the bypass valve assembly (48).
Fasten with a lock washer (37) and a nut (33).
85. Select two each:
(31) 802-551C, HHCS 1/4-20X2 1/4 GR5,
(39) 804-075C, WASHER FLAT 1/4 USS PLT,
(36) 804-006C, WASHER LOCK SPRING 1/4 PLT,
(32) 803-006C, NUT HEX 1/4-20 PLT.
From outside the mount, insert each bolt (31), then
through the plate hole
➄
into the notches of the
shuttle valve (46) and loosely fit a flat washer (39),
lock washer (36) and nut (32).
86. Snug the valve assembly (48)(46) against the
mounting plate (23), seat all bolts deeply in notches,
and tighten all bolts and nuts.
Figure 17
Open Center Fasteners (R)
25181
➀
➁
➂
44
45
39
36
32
T
B
F
R
L
R
31 32 36
39
31
31
47
32
36
39
39
23
Figure 18
Open Center Fasteners (L)
25182
31
➄
➃
48
28
T
B
F
R
L
R
40
32
36
45
40
33 37
39
23