Tweco 250i Multi Process Welding Inverter 2RT Wire Feeder User Manual
250i operating manual, Transmig, Multi process welding inverter
Table of contents
Document Outline
- SECTION 1:ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- SECTION 2: INTRODUCTION
- SECTION 3: INSTALLATION OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 Electromagnetic Compatibility
- 3.06 Power Source Controls, Indicators and Features
- 3.07 Advanced Features Details
- 3.08 Optional Wire Feeder Controls, Indicators and Features
- 3.09 Optional Wire Feeder Set Up MIG (GMAW) Welding with Gas Shielded MIG Wire
- 3.10 Optional Wire Feeder Set-up for MIG (FCAW) Welding with Gasless MIG Wire
- 3.11 Fitting of Optional Roll Cage
- 3.12 Assembly and Fitting of Optional Welding Trolley
- 3.13 Attaching the Tweco Professional MIG Torch (Euro)
- 3.14 Installing a Handispool (200mm diameter)
- 3.15 Installing a Standard Spool (300mm diameter)
- 3.16 Inserting Wire into the Feed Mechanism
- 3.17 Feed Roller Pressure Adjustment
- 3.18 Feed Roller Alignment
- 3.19 Changing the Feed Roll
- 3.20 Input And Output Wire Guide Installation
- 3.21 Wire Reel Brake
- 3.22 Shielding Gas Regulator Operating Instructions
- 3.23 Set-up MIG (GMAW) Welding with Gas Shielded MIG Wire
- 3.24 Set-up for MIG (FCAW) Welding with Gasless MIG Wire
- 3.25 Set-up for LIFT TIG (GTAW) Welding
- 3.26 Set-up for Metal Manual Metal Arc Welding (MMAW)
- SECTION 4:BASIC WELDING GUIDE
- SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- SECTION 6: KEY SPARE PARTS
- APPENDIX 1: Options and Accessories
- APPENDIX 2: TRANSMIG 250i CIRCUIT DIAGRAM
- CIGWELD LIMITED WARRANTY
- TERMS OF WARRANTY – APRIL 2010
- WARRANTY SCHEDULE – APRIL 2010
- GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
- SECTION 1:ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- SECTION 2: INTRODUCTION
- SECTION 3: INSTALLATION OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 Electromagnetic Compatibility
- 3.06 Power Source Controls, Indicators and Features
- 3.07 Advanced Features Details
- 3.08 Optional Wire Feeder Controls, Indicators and Features
- 3.09 Optional Wire Feeder Set Up MIG (GMAW) Welding with Gas Shielded MIG Wire
- 3.10 Optional Wire Feeder Set-up for MIG (FCAW) Welding with Gasless MIG Wire
- 3.11 Fitting of Optional Roll Cage
- 3.12 Assembly and Fitting of Optional Welding Trolley
- 3.13 Attaching the Tweco Professional MIG Torch (Euro)
- 3.14 Installing a Handispool (200mm diameter)
- 3.15 Installing a Standard Spool (300mm diameter)
- 3.16 Inserting Wire into the Feed Mechanism
- 3.17 Feed Roller Pressure Adjustment
- 3.18 Feed Roller Alignment
- 3.19 Changing the Feed Roll
- 3.20 Input And Output Wire Guide Installation
- 3.21 Wire Reel Brake
- 3.22 Shielding Gas Regulator Operating Instructions
- 3.23 Set-up MIG (GMAW) Welding with Gas Shielded MIG Wire
- 3.24 Set-up for MIG (FCAW) Welding with Gasless MIG Wire
- 3.25 Set-up for LIFT TIG (GTAW) Welding
- 3.26 Set-up for Metal Manual Metal Arc Welding (MMAW)
- SECTION 4:BASIC WELDING GUIDE
- SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- SECTION 6: KEY SPARE PARTS
- APPENDIX 1: Options and Accessories
- APPENDIX 2: TRANSMIG 250i CIRCUIT DIAGRAM
- CIGWELD LIMITED WARRANTY
- TERMS OF WARRANTY – APRIL 2010
- WARRANTY SCHEDULE – APRIL 2010
- GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
- SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- CIGWELD LIMITED WARRANTY
- TERMS OF WARRANTY - APRIL 2010
- WARRANTY SCHEDULE - APRIL 2010