Trusted, Communication interface t8151b – Rockwell Automation T8xxx Trusted Communications Interface User Manual
Page 50
Trusted
TM
Communication Interface T8151B
Issue 21 Apr 10
PD-T8151B
50
From
To
Communication
Interface (PL5)
Interface
Adapter (J3)
9 Way D-type
25 Way D-type
DIN41612
Socket
9 way Phoenix
Contact Socket
To DTE
(Socket)
To DCE
(Plug)
To DTE
(Socket)
To DCE
(Plug)
A5 (TXD1)
1 (TXD)
2 (RXD)
3 (TXD)
3 (RXD)
2 (TXD)
C6 (RXD1)
2 (RXD)
3 (TXD)
2 (RXD)
2 (TXD)
3 (RXD)
A6 (RTS1)*
3 (RTS)*
8 (CTS)
7 (RTS)
5 (CTS)
4 (RTS)
A7 (CTS1)*
4 (CTS)*
7 (RTS)
8 (CTS)
4 (RTS)
5 (CTS)
C9 (GND1)
5 (GND)
5 (GND)
5 (GND)
7 (GND)
7 (GND)
B7 (DSR1)*
6 (DSR)*
4 (DTR)
6 (DSR)
20 (DTR)
6 (DSR)
C7 (DCD1)*
7 (DCD)*
4 (DTR)
1 (DCD)
20 (DTR)
8 (DCD)
B6 (DTR1)*
8 (DTR)*
6(DSR)
4 (DTR)
6 (DSR)
20 (DTR)
B6 (DTR1)*
8 (DTR)*
1(DCD)
-
8 (DCD)
-
C8 (RI1)*
9 (RI)*
Not
Connected
9 (RI)
Not
Connected
22 (RI)
Note:
GND refers to Signal Ground. This should not be connected to chassis ground e.g. Pin 1 on 25 Way D-types.
* Signals shown for completeness only, not used in the Communication Interface.
Table 19 Cable wiring for CI Port 1
Table 20 below shows some alternatives for the wiring for Port 2 when using a cable.
From
To
Communications
Interface (PL5)
Interface
Adapter (J7)
9 Way D-type
25 Way D-type
DIN41612
Socket
5 way Phoenix
Contact Socket
To DTE
(Socket)
To DCE
(Plug)
To DTE
(Socket)
To DCE
(Plug)
A11 (TXD2)
1 (TXD)
2 (RXD)
3 (TXD)
3 (RXD)
2 (TXD)
C11 (RXD2)
2 (RXD)
3 (TXD)
2 (RXD)
2 (TXD)
3 (RXD)
B11 (RTS2)*
3 (RTS)*
8 (CTS)
7 (RTS)
5 (CTS)
4 (RTS)
C12 (CTS2)*
4 (CTS)*
7 (RTS)
8 (CTS)
4 (RTS)
5 (CTS)
C13 (GND2)
5 (GND)
5 (GND)
5 (GND)
7 (GND)
7 (GND)
Note:
GND refers to Signal Ground. This should not be connected to chassis ground e.g. Pin 1 on 25 Way D-types.
* Signals shown for completeness only, not used in the Communications Interface.
Table 20 Cable wiring for CI Port 2
Figure 19 below shows the connection of the Communication Interface front panel port. This also
applies to the processor front panel port. These are normally connected using a TC-304-01
maintenance cable.