Stainless Works 350-199 Dodge Challenger / Charger / Magnum 5.7/6.1L 2005-2010 AIRAID Intake System - Manual

1. Disconnect the negative battery cable.
If you are working on a 5.7L, first remove
the engine beauty cover by lifting it up off of
the grommets. Next, loosen the hose clamp
that holds the factory intake tube to the
throttle body.
6. With a 10mm socket, remove and save
the bolt that holds the factory air filter base
to the radiator support. Remove the air filter
base from the vehicle.
Installation Instructions
Part Number 350-199
2006-10 Dodge Charger 5.7L, 6.1L
2005-08 Dodge Magnum 5.7L, 6.1L
2005-10 Chrysler 300 5.7L, 6.1L
2008-10 Dodge Challenger 5.7L, 6.1L
Packing List:
#1 700-469 Airaid Premium Filter 1
#2 KIT1931MAFC MAF Panel 1
#3 KIT1931BPC Back Panel 1
#4 KIT193T Airaid Intake Tube 1
#5 KIT1121MAFADA Filter Adapter 1
#6 KIT199RSC Rear Support Bracket 1
#7 KITHUMPHS05 Urethane Hump Hose 1
#8 KITRDCR04 Reducing Coupler 1
#9 KITELBOW06 Breather Hose 1
#10 KITWSTRIP02 Weather Strip 20 1/2” 1
KIT199HP Hardware & Instructions 1
#11 KIT15BHC3100 3/8-16 x 1” Button Head Bolt 1
#12 KIT31NWUSPZ 3/8” Flat Washer 1
#13 KIT15DHC3050 ¼ - 20 x 1/2” Button Head Bolt 6
#14 KIT09FWX019 ¼” Flat Washer 6
#15 KIT1420WZZF 1/4” Serrated Nut 3
#16 KIT6C31MXPPZ 6-32 x 5/16” Screw 4
#17 KIT6NWSAPZ #6 Flat Washer 4
#18 KIT6CNKEPZ 6-32 Keps Nut 4
#19 KITHS52 #52 Hose Clamp 2
#20 KITHS72 #72 Hose Clamp 2
#21 KITGRMT02 Grommet 1
#22 KITNUT01 Well Nut 1
7. Assemble the two Cool Air Dam (CAD)
panels (#2, #3) using five 6-32 x 5/16”
screws (#16), #6 flat washers (#17), and 6-
32 keps nuts (#18). 9. Slip the well nut (#22) into the hole in
the inner fender.
10. Install the CAD into the vehicle. Re-
install the factory bolt removed in step #6
thru the CAD and into the radiator support.
Next install the 3/8-16 x 1” button head
bolt (#11) and 3/8” flat washer (#12) thru
the CAD and into the well nut. Tighten
both bolts. 12. Install the rear support bracket (#6)
from the CAD to the inner fender using
three ¼ - 20 x 1/2” button head bolts (#13),
¼” flat washers (#14), 1/4” serrated nuts
(#15), and the 10mm factory nut removed
in step #11.
8. Next, install the filter adapter (#5) using
three ¼ - 20 x 1/2” button head bolts (#13),
and ¼ flat washers (#14).
11. Remove the 10mm nut from the stud
on the driver’s side inner fender and save it
for the next step.
3. Pull both lockdown tabs towards you on
the factory airbox lid to remove the lid from
the base.
4. Lift the intake tube towards you, and
without disconnecting the wiring harness,
gently remove the temperature sensor from
the factory intake tube, and set it aside.
2. Disconnect the breather hose from the
factory airbox lid.
5. Remove the factory intake hose and lid
assembly from the vehicle. Remove the
factory air filter.
Tools Required For Installation:
5/32”, 7/32” Allen Wrenches
5/16”, 7/16”, & 10mm Sockets
Ratchet & Extension
Phillips Screwdriver