Skyjacker FBLxx D.O.T. BRAKELINE - Manual (Page 2)

NOTES:
GMC/CHEVY - FRONT: Stock nuts may be re-used on
some models straight axle models. '88-98 Models -
Use line clamps & self-tapping screws (See Below) &
mount to upper A-arm.
GMC / CHEVY - REAR: Hose is furnished with a 1/4"
bolt and flat washers to accept smaller upper hole.
Use a flat washer on each side of bolt.
EXPLORER/RANGER / BRONCO II - FRONT: The
appropriate place to tie brake line will be to the coil
springs. On 1989-97 models, screw the brass T-Block
into the top of the driver's side line before installing.
Models with Front & Rear ABS brakes do not use the
T-Block on the driver's side.
F150 / BRONCO - FRONT: The appropriate place to
tie brake line is the coil springs.
'78-'79 FORD - FRONT: Remove the front axle mount-
ing bracket from the stock hose and drill out the brack-
et to accept the bolt and attach the bracket to the new
line.
JEEP YJ / 66-77 BRONCO - FRONT: Included are 2
line clamps (1 per side) to secure the hose to the
upper frame.
Affix line clamp around new brake line and secure with
the self tapping screw supplied as shown in illustration
below. NOTES:
GMC/CHEVY - FRONT: Stock nuts may be re-used on
some models straight axle models. '88-98 Models -
Use line clamps & self-tapping screws (See Below) &
mount to upper A-arm.
GMC / CHEVY - REAR: Hose is furnished with a 1/4"
bolt and flat washers to accept smaller upper hole.
Use a flat washer on each side of bolt.
EXPLORER/RANGER / BRONCO II - FRONT: The
appropriate place to tie brake line will be to the coil
springs. On 1989-97 models, screw the brass T-Block
into the top of the driver's side line before installing.
Models with Front & Rear ABS brakes do not use the
T-Block on the driver's side.
F150 / BRONCO - FRONT: The appropriate place to
tie brake line is the coil springs.
'78-'79 FORD - FRONT: Remove the front axle mount-
ing bracket from the stock hose and drill out the brack-
et to accept the bolt and attach the bracket to the new
line.
JEEP YJ / 66-77 BRONCO - FRONT: Included are 2
line clamps (1 per side) to secure the hose to the
upper frame.
Affix line clamp around new brake line and secure with
the self tapping screw supplied as shown in illustration
below.
Self Tapping Screw Self Tapping Screw
Line Clamp Line Clamp
Brake Line Brake Line
PRODUCT USE INFORMATION:
Check any nut and/or bolt in the area for tightness.
It is the customers' responsibility to check brake lines
for abrasion, leaks and/or brake line fittings for tight-
ness after the first 100 miles and after every off-road
activity.
Inspection should be done periodically by a profession-
al mechanic to be sure everything is in workable,
functionable order.
Skyjacker will not be responsible for any altered prod-
uct or any improper installation or use of the product.
Skyjacker does have the option to inspect any and all
lines before any warranty consideration is approved.
If you have any questions concerning the product, call
our main office at (318) 388-0816
PRODUCT USE INFORMATION:
Check any nut and/or bolt in the area for tightness.
It is the customers' responsibility to check brake lines
for abrasion, leaks and/or brake line fittings for tight-
ness after the first 100 miles and after every off-road
activity.
Inspection should be done periodically by a profession-
al mechanic to be sure everything is in workable,
functionable order.
Skyjacker will not be responsible for any altered prod-
uct or any improper installation or use of the product.
Skyjacker does have the option to inspect any and all
lines before any warranty consideration is approved.
If you have any questions concerning the product, call
our main office at (318) 388-0816