111 accumulator: maintenance overview, 111 accumulator: maintenance overview 93 – MTS 318 Load Unit User Manual
Page 93
Routine Maintenance Overview Checklist
318 Load Unit
Maintenance
93
C. Turn the load unit’s hydraulic pressure to off.
Anti-Rotate Actuator—Tightening the Cap Screws
D. If your load unit has an antirotate actuator, tighten the four antirotate
cap screws to a torque listed in the following table. (The actuator force
rating is stated on an identification plate at the rear of the load unit.)
111 Accumulator: Maintenance Overview
Maintaining the proper pressure level for your accumulators is essential for
optimum system performance and component life. Review the following figure
to familiarize yourself with the accumulator components and their locations.
Also review the following guidelines before performing any procedure.
A
CTUATOR
F
ORCE
R
ATING
T
ORQUE
R
ATING
25 kN (5.5 kip)
3.7 N·m (2.7 lbf·ft)
11–500 kN (11–110 kip)
48 N·m (35 lb·ft)
Unscrew/Tighten
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)