Landoll 9650 Field Cultivator - Manual (Page 55)

ASSEMBLY INSTRUCTIONS
3-15
Hydraulic Installation
NOTES
See Figures 3-7 through 3-10 for hydraulic cylinder
fittings (factory installed and those installed during
setup.)
Refer to Figures 3-7 and 3-8 for lift and fold hydraulic
diagrams for 9650-38 and 9650-42 models.
Refer to Figures 3-9 and 3-10 for lift and fold hydraulic
diagrams for 9650-46 and 9650-50 models.
Refer to Figure 3-6 for lift and fold manifold details for all
models.
Refer to Figure 3-11 for hydraulic cylinder installation for
all models.
1. Attach the base end of each 4 x 30 hydraulic cylinder
to the fold cylinder mount on the center frame with
clevis and roll pins provided with each cylinder as
shown in Figure 3-11. Position the cylinders so the
hydraulic ports point to rear of front and to front on
the rear and toward the center of the machine.
2. Using 1-1/4 x 6-1/8 fold pin, 1-1/4N flat washers, and
5/16 x 2-1/2 spring slotted pins, attach the rod end of
the 4 x 30 cylinders to the slotted mounts on the
inner wing frames (See Figure 3-11.)
3. Attach base of (4) 3-1/2 x 16 hydraulic cylinders to
mount on inner wing at front of the machine using
clevis and roll pins provided with each cylinder.
4. Using a 1-1/4-7 x 7 hex head cap screw, flat
washers, wing extension roller, and hex lock nut,
attach the rod end of the 3-1/2 x 16 hydraulic
cylinders to the fold links on the double hinge (See
Figure 3-11.) Do not overtighten screws. Fold links
should pivot freely without binding or dragging.
Tighten screws to remove excess slack, but still allow
fold links to flex.
NOTE
Rod ends of fold cylinders need to be left unassembled
until fold hydraulic system is fully charged with oil to
prevent machine damage.

CAUTION
5. Install 90 degree regular adapter fittings in both ends
of all lift cylinders (4 x 10, 3-3/4 x 10, and 3-1/2 x 10)
(See Figures 3-9 and 3-6.)
6. Install base end of lift cylinders (4 x 10, 3-3/4 x 10,
and 3-1/2 x 10) to lift cylinder arm using clevis and
roll pins provided with each cylinder (See
Figure 3-11.) Position so that the cylinder ports are
on top.
7. Install base end of 1-3/4 x 6 fold lock cylinders to the
transport lock plate on the center frame lift using
3/4-10 x 2-1/2 hex head cap screw and hex lock nut.
8. Install rod end of lift cylinders and transport lock
(outer tire removed) to center frame using 1 x
4-19/32 pin, 5/16 x 2-1/2 spring slotted pin, and flat
washer (See Figure 3-11.) Note that the pin head will
be on the outside of the machine.
9. Install rod end of 1-3/4 x 6 fold lock cylinders to the
top of the transport locks using 3/4-10 x 9-1/2 hex
head cap screw and hex lock nut. Do not overtighten
as these must be allowed to pivot.
10. Install rod end of lift cylinders to the wings using the
clevis pin that comes with each cylinder.
11. Install the 16 port manifold assembly to the manifold
bracket on the rear of the center frame using 1/2-13 x
3-1/2 hex head cap screws and hex lock nuts.
12. Attach the 8 port manifold assembly to the front
manifold bracket on the implement using 1/2-13 x
3-1/2 hex head cap screws and hex lock nuts.Install
lift system hoses (See Figures 3-9 and 3-6.) Wrap
lift system hoses with blue hose wrap.
13. Attach hose clamps to the hitch using 3/8-16 x 2-1/2
hex head cap screws and hex lock nuts.
14. Attach hose clamps to the center frame, inner wings,
and outer wings using 3/8-16 x 2-3/4 hex head cap
screws and hex lock nuts (See Figures 2-1 and 2-2.)
15. Install lift system hoses per Figure 3-7 (9650-38 and
9650-42) or Figure 3-9 (9650-46 and 9650-50.)
Wrap lift system hoses with blue hose wrap.
16. Install fold system hoses per Figure 3-8 (9650-38
and 9650-42) or Figure 3-10 (9650-46 and
9650-50.) Wrap fold system hoses with yellow hose
wrap.
Restrictors are installed in the rod end of wing
fold cylinders to prevent uncontrolled dropping
of wings. Removal of these restrictors, or
improper installation can result in serious
damage to the implement. See Figures 3-8 and
3-10 for proper restrictor fitting identification and
location.