HMC Electronics 101-1 Permabond 101 Cyanoacrylate Adhesive, General Purpose, Wicking Type, Plastic Bonding - Manual (Page 2)

The information given and the recommendations made herein are based on our research and are believed to be accurate but no guarantee of their accuracy is made. In every case
we urge and recommend that purchasers before using any product in full-scale production make their own tests to determine to their own satisfaction whether the product is of
acceptable quality and is suitable for their particular purpose under their own operating conditions. THE PRODUCTS DISCLOSED HEREIN ARE SOLD WITHOUT ANY WARRANTY
AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED.
No representative of ours has any authority to waive or change the foregoing provisions but, subject to such provisions, our engineers are available to assist purchasers in adapting our products
to their needs and to the circumstances prevailing in their business. Nothing contained herein shall be construed to imply the non-existence of any relevant patents or to constitute a permission,
inducement or recommendation to practice any invention covered by any patent, without authority from the owner of this patent. We also expect purchasers to use our products in
accordance with the guiding principles of the Chemical Manufacturers Association’s Responsible Care® program.
Global TDS Revision 1 Page
2/2
Chemical Resistance
0
20
40
60
80
100
120
A
ir
R
ef
er
en
ce
95
%
R
el
ati
ve
H
um
id
ity
4
0°
C
U
nl
ea
de
d
G
as
ol
in
e
M
oto
r O
il
@
40
°C
W
at
er
E
th
an
ol
Is
op
ro
pa
no
l
Specimens were immersed for 1000 hours at 22°C (unless otherwise
stated)
Additional Information
This product is not recommended for use in contact
with strong oxidizing materials and polar solvents
although will withstand a solvent wash without any
bond strength deterioration. Users are reminded
that all materials, whether innocuous or not, should
be handled in accordance with the principles of good
industrial hygiene. Full information can be obtained
from the Material Safety Data Sheet.
Surface Preparation
Surfaces should be clean, dry and grease‐free before
applying the adhesive. Use a suitable solvent (such as
acetone or isopropanol) for the degreasing of
surfaces. Some metals such as aluminium, copper
and its alloys will benefit from light abrasion with
emery cloth (or similar), to remove the oxide layer.
Directions for Use
1) Apply the adhesive sparingly to one surface
(usually 1 drop is sufficient).
2) Bring the components together quickly and
correctly aligned.
3) Apply sufficient pressure to ensure the
adhesive spreads into a thin film.
4) Do not disturb or re‐align until curing is
achieved, normally in a few seconds.
5) Any surplus adhesive can be removed with a
suitable solvent.
NB:
For difficult or porous surfaces using a
Permabond activator is recommended.
If bonding polypropylene, polyethylene, PTFE or
silicone, prime first with Permabond Polyolefin
Primer.
Storage & Handling
Storage Temperature 2 to 7°C (35 to 45°F)
Shelf Life
Stored in original unopened containers
12 months
Allow adhesive to reach room temperature
before opening bottle to prevent condensation
inside the bottle which can reduce shelf life.
Contact Permabond:
Europe: Tel. +44 (0)1962 711661 US: Tel. +1 732‐868‐1372
UK Helpline: 0800 975 9800 Helpline: 800‐640‐7599
Deutschland: 0800 10 13 177 [email protected]
France: 0805 11 13 88 Asia: Tel. +86 21 5773 4913
[email protected] [email protected]
www.permabond.com
%
Strength
retention
Documentation Provided By HMC Electronics
33 Springdale Ave. Canton, MA 02021
http://www.hmcelectronics.com
(800) 482-4440