Direct drive, Error messages and function codes – COATS 850 Solid State Wheel Balancer User Manual
Page 17
COATS 850SS Wheel Balancer • 11
Error Messages and
Function Codes
Error Messages
The following codes may appear in the weight dis-
plays to indicate a problem with the balancer.
A ERR - The distance from the balancer to the inner
rim of the wheel was not entered.
W ERR - The width of the wheel was not entered.
D ERR - The diameter of the wheel was not
entered.
ERR 1 - Wheel moved, but stopped for some
reason.
ERR 2 - Wheel did not come up to speed in 26
seconds.
ERR 3 - Wheel did not turn when the START button
was pushed. Alternatively, no optical
signals.
ERR 4 - Wheel rotates counter-clockwise.
ERR 5 - Cycle did not complete within 26 seconds.
ERR 6 - No power to optical encoder.
ERR 7 - Overspeed.
ERR 8 - Time to set gain is too long.
ERR 9 - Measurement time is too long.
ERR 10 - Measurement speed is too slow.
HOOD - Hood up during wheel motion.
HUB - Wheel reached speed too quickly.
Function Codes
CODE 9 1 A - Perform Calibration
CODE 0 3 A - Clear
CODE 0 4 A - Toggle High Resolution Mode on/off
CODE 0 5 A - Toggle Gram/Ounce Mode on/off
CODE 3 7 A - Adjust top-dead-center position error
Direct Drive
- 16 Bit PCB & Metal Arm Temporary (4 pages)
- 520 Wheel Lift (12 pages)
- 700 Decal Location (1 page)
- AirNut (12 pages)
- Application Chart, Balancing Solutions (12 pages)
- Autoflate Nitrogen (1 page)
- Balancer Adapter Wall Storage Board Kit (1 page)
- Balancer Adapter, 5 lug x 135mm Bolt Pattern (1 page)
- Balancer Adapter, 5 lug x 150mm Bolt Pattern (1 page)
- Balancer Adapter, 5 lug x 4.750 Bolt Pattern (1 page)
- Balancer Adapter, 5 lug x 5.5 Bolt Pattern (1 page)
- Balancer Adapter, 6 lug x 150mm Bolt Pattern (1 page)
- Balancer Adapter, 6 lug x 5.5 Bolt Pattern (1 page)
- Balancer Adapter, 8 lug x 170mm Bolt Pattern (1 page)
- Balancer Adapter, 8 lug x 180mm Bolt Pattern (1 page)
- Balancer Adapter, 8 lug x 6.5 Bolt Pattern (1 page)
- Conversion Instructions (1 page)
- Extended Balancer Stub Shaft (1 page)
- Fixed Finger Plates (2 pages)
- Hood Installation (1 page)
- Hood Installation Instruction (1 page)
- Hood Installation Sheet (1 page)
- Hood Installation Tip (1 page)
- Hubnut Removal (1 page)
- Side Accessory Tray (1 page)
- Kit 1.125-inch, Kit 40 mm, Light Truck Cone (1 page)
- Kit 1.125-inch, Kit 40 mm, XL Pressure Drum (1 page)
- Kit 8111177 Three Phase to Single Phase Conversion (1 page)
- Kit 8111864 Motorcycle Wheel Adapter (4 pages)
- Kit 8111935 Light Truck Back Cone Spacer (1 page)
- Kit 8112877 Touch Panel Replacement (2 pages)
- Kit 8113082 40mm Conversion Shaft (1 page)
- Kit 8113223 (1.125-inch), Kit 8113228 (40 mm), VW/Porsche Adapter (1 page)
- Kit 8113592, Wheel Lift Link (1 page)
- Kit 8113645 Radial Runout Sensor Adjustment Kit (2 pages)
- Kit 8113860 Splash Guard (1 page)
- Kit 8113881 Printer Serive (1 page)
- Kit 8113883 Printer Bracket Serive (1 page)
- Kit 8113887 XR 1800 Upgrade to XR 1850 (2 pages)
- Kit 8113893 Lateral Run Out Service (1 page)
- Kit 8113900 Monitor Replacement (1 page)
- Kit 8113932 16 Bit PCB & Metal Arm (1 page)
- Kit 8114025 PCB Assembly (1 page)
- Kit 8114105 PCB Assembly Kit (1 page)
- Kit 8114155 Serial Loader (4 pages)