COATS Balancer Adapter Wall Storage Board Kit User Manual
Balancer adapter wall storage board kit, Balancing solutions, Ạạ ả ả
8113225 02 02/08
© COPYRIGHT ALL RIGHTS RESERVED PRINTED IN U.S.A.
Balancer Adapter
Wall Storage Board Kit
Balancing Solutions
Before You Begin
The Wall Storage Board Kit consists of the following parts:
Item
Part No. Qty. Description
Ạ
8113093
1
Storage Board
ạ
8113094
13
Hook
Ả
8107091
13
Grip
ả
8106303
26
3/8-16 UNC Locknut
Verify that you have received all of the parts listed.
Assembly and Installation
1. Install the Grips onto the Hooks if not already installed. (Fig. 1)
2. Install each Hook onto the Storage Board using two 3/8-16 UNC
Locknuts as shown in figure 1. Handtighten the Locknuts (very snug),
leaving the threaded portion of the Hook flush with the Locknut. Make
sure the Hooks are pointing upward toward the label.
3. Mount the assembled Storage Board (fig. 2) in the desired location.
Figure 2 - Assembled Wall Storage Board
Figure 1 - Hook Assembly Diagram
Ạ
ạ
Ả
ả
Mounting
Hole
Mounting
Hole
Mounting
Hole
Mounting
Hole
- 16 Bit PCB & Metal Arm Temporary (4 pages)
- 520 Wheel Lift (12 pages)
- 700 Decal Location (1 page)
- AirNut (12 pages)
- Application Chart, Balancing Solutions (12 pages)
- Autoflate Nitrogen (1 page)
- Balancer Adapter, 5 lug x 135mm Bolt Pattern (1 page)
- Balancer Adapter, 5 lug x 150mm Bolt Pattern (1 page)
- Balancer Adapter, 5 lug x 4.750 Bolt Pattern (1 page)
- Balancer Adapter, 5 lug x 5.5 Bolt Pattern (1 page)
- Balancer Adapter, 6 lug x 150mm Bolt Pattern (1 page)
- Balancer Adapter, 6 lug x 5.5 Bolt Pattern (1 page)
- Balancer Adapter, 8 lug x 170mm Bolt Pattern (1 page)
- Balancer Adapter, 8 lug x 180mm Bolt Pattern (1 page)
- Balancer Adapter, 8 lug x 6.5 Bolt Pattern (1 page)
- Conversion Instructions (1 page)
- Extended Balancer Stub Shaft (1 page)
- Fixed Finger Plates (2 pages)
- Hood Installation (1 page)
- Hood Installation Instruction (1 page)
- Hood Installation Sheet (1 page)
- Hood Installation Tip (1 page)
- Hubnut Removal (1 page)
- Side Accessory Tray (1 page)
- Kit 1.125-inch, Kit 40 mm, Light Truck Cone (1 page)
- Kit 1.125-inch, Kit 40 mm, XL Pressure Drum (1 page)
- Kit 8111177 Three Phase to Single Phase Conversion (1 page)
- Kit 8111864 Motorcycle Wheel Adapter (4 pages)
- Kit 8111935 Light Truck Back Cone Spacer (1 page)
- Kit 8112877 Touch Panel Replacement (2 pages)
- Kit 8113082 40mm Conversion Shaft (1 page)
- Kit 8113223 (1.125-inch), Kit 8113228 (40 mm), VW/Porsche Adapter (1 page)
- Kit 8113592, Wheel Lift Link (1 page)
- Kit 8113645 Radial Runout Sensor Adjustment Kit (2 pages)
- Kit 8113860 Splash Guard (1 page)
- Kit 8113881 Printer Serive (1 page)
- Kit 8113883 Printer Bracket Serive (1 page)
- Kit 8113887 XR 1800 Upgrade to XR 1850 (2 pages)
- Kit 8113893 Lateral Run Out Service (1 page)
- Kit 8113900 Monitor Replacement (1 page)
- Kit 8113932 16 Bit PCB & Metal Arm (1 page)
- Kit 8114025 PCB Assembly (1 page)
- Kit 8114105 PCB Assembly Kit (1 page)
- Kit 8114155 Serial Loader (4 pages)