B&W Trailer Hitches 1067R - Manual

B&W Trailer Hitches
1216 Hawaii Road / PO Box 186
Humboldt, KS 66748
800.248.6564
620.473.3664
Fax:620.473.3766
Turnoverball TM Gooseneck Hitch Installation Instructions
Call or Email us for Installation Support Model 1067R
[email protected] / www.turnoverball.com
BEFORE INSTALLING
OVERHEAD LIFTING DEVICE
An overhead-lifting device, such as chain falls, engine hoist, or cable come-a-long, can be used to lift the center section of the hitch in
place. Lower a loop of rope or chain through the 4” hole in the truck bed floor and attach it to the latch pin in the round hitch receiver
tube in the center section. Use the lifting device to raise the center section until the round hitch receiver tube that protrudes from
the center section fits in the 4” hole in the truck bed floor. Maintaining upward pressure may facilitate fastening the crossmember
to the center section, especially if the truck bed floor has been distorted downward from heavy use. If you use an overhead-lifting
device, it should be disconnected before squaring the center section across the frame, installing the sideplates and torquing fasteners.
WARNING
Most trucks have FUEL LINES and/or BRAKE LINES and/or ELECTRICAL WIRES located along the frame rails where B&W Turnoverball™
hitches install. Carefully examine the location of fuel lines, brake lines and electrical wires BEFORE INSTALLATION. Be certain you
will not damage fuel lines, brake lines or electrical wires when positioning hitch components, drilling holes and tightening fasteners.
The fuel tank vent, located on top of the gas tank, can be easily damaged during the installation of the hitch components. Care must
be taken when positioning the front crossmember and center section components.
2001-2010 Chevrolet & GMC
3/4 Ton Heavy Duty (New Frame & Body) Short & Long Bed Trucks
2007-2010 Chevrolet & GMC
1 Ton New Frame & Body (1 Ton Requires New Bed with only 1 Crossmember over axle)
NOTE: We recommend reading instructions before beginning the installation.
WARNING: The tow vehicle’s towing capacities should under NO circumstances be exceeded.
Mounting Kit Box (GNRM1067)
ITEM DESCRIPTION QTY
1 Driver Side Front Sideplate 1
2 Passenger Side Front Sideplate 1
3 Driver Side Rear Sideplate 1
4 Passenger Side Rear Sideplate 1
5 Front Crossmember 1
6 Rear Crossmember 1
7 Relay Bracket 1
8 8-1/4” X 4-1/4” X 1/2” U-Bolt 2
Mounting Kit Bolt Bag
9 Rear Sideplate Bushing 2
1/2” X 1-1/4” Carriage Bolt 6
1/2” X 1-1/2” Cap Screw 11
1/2” Flat Washer 17
1/2” Lock washer 21
1/2" Finish Nut 15
3/4" X 2-1/2" Cap Screw 2
3/4" Flat Washer 2
3/4” Lock Washer 2
3/4" Finish Nut 2
O-Ring 1
Center Box (GNRC959N)
ITEM DESCRIPTION QTY
10 Center Section 1
11 2-5/16" Ball 1
12 Latch pin Handle 1
Safety Chain Kit Bolt Bag
13 1/2” U-Bolt 2
14 Conical Springs 4
15 1/2” Lock Nut 4
5/16” X 3/4” Carriage Bolt 1
5/16” X 3/4” Cap Screw
1
5/16” Lock Nut 1
NOTICE: This product was designed to fit vehicles in their original, “as manufactured” condition. Compatibility with vehicles having
replacement parts, or other modifications is not guaranteed. Inspect vehicle for modifications before installation of this product.