B&W Trailer Hitches Turnoverball Model 1306 (Dodge) - Manual

Turnover Ball TM Gooseneck Hitch Installation Instructions
Call or Email us for Installation Support
Model 1306R
Copyright 2010
B&W Custom Truck Beds, Inc.
ALL RIGHTS RESERVED
To install the safety chain U-bolts it is necessary to drill four 1/2” holes through the truck bed floor. Drill the holes
from beneath the truck, through the four holes located in the 906R center section. Drop a U-bolt through each pair of
holes from the top side of the truck bed floor. Place a taperd spring and center lock nut on each of the four legs. Tighten
the center lock nuts until flush with the bottom of the U-Bolts.
STEP 7
1306R 04 05 2010
Hardware Kit
Parts List
[email protected]
www.turnoverball.com
B&W Trailer Hitches
1216 HWY 224 / PO Box 186
Humboldt, KS 66748
620.473.3664
800.248.6564
Fax:620.473.3766
STEP 5
Tighten all hardware in this order:
1) Tighten all 906R center section hardware to 80 ft. lbs.
2) Check to ensure that the hitch is square by measuring the space between the front cross member of the hitch
and the bed cross member so that the space is equal on each side of the truck.
3) Tighten the gold U-bolts to 60ft. lbs.
4) Tighten the 5/8” X 7 ½” hex cap screws to 60 ft. lbs.
5) Tighten the hardware that holds the side plates to the cross members to 80 ft. lbs.
Dodge 2003-2010
¾, & 1 Ton Long & Short Bed
Two & Four-Wheel Drive And
½, ¾, & 1 Ton Mega Cab Short Bed
11 - ½” X 1 ½” hex cap screw
9 - ½” hex finish nut
15 - ½” split lock washer
11 - ½” flat washer
2 - 4” X 6 ½” gold U-bolt
2 - 5/8” X 7 ½” hex cap screw
2 - 5/8” hex finish nut
2 - 5/8” split lock washer
4 - 5/8” flat washer
1 - 5/16” X 1” carriage bolt
1- 5/16” flange nut
Safety Chain Kit
2 - ½” U-bolt
4 - ½” lock nut
4 - spring
1 - 3/8” x ¾” hex cap screw
1- Front Cross Member
2- Rear Cross Member
3 - 906R center Section
4 - Left Side plate
5 - Right Side Plate
6 - 4” X 6 ½” Gold U-bolt
7 - 5/8” X 7 ½” Hex Cap Screw
8 - ½” X 1 ½” X 3 1/8” Silver U-bolt
9 - Tapered Spring
10 - ½” Center Lock Nut
11 - 5/8” Flat Washer
12 - 5/8” Split Lock Washer
13 - 5/8” Hex Finish Nut
14 - Latch Pin Handle
NOTE:
We recommend reading instructions before beginning the installation.
STEP 6 – INSTALL LATCH PIN RELEASE HANDLE
WARNING: LATCH PIN WILL NOT FUNCTION PROPERLY IF HANDLE IS NOT INSTALLED CORRECTLY.
Install the handle from underneath the truck by inserting it through the slot in the end of the center section toward
the driver’s side rear tire as shown. Attach the handle to the latch pin as shown with the handle on the “cab side” of
the square tab welded to the pin. The head of the bolt must be on the handle side, and the lock nut must be on the
tab side. The tab is welded to the pin in an offset
position so that the handle will be lined up over
the center of the pin. If the handle is fastened
to the other side of the tab, the handle will not
function properly. When installed correctly the
latch pin may be disengaged from the ball by
pulling on the handle from the driver’s side
wheel well and rotating the handle clockwise.