Cirrus Logic CS42L73 - Manual (Page 27)

DS882F1 27
CS42L73
SERIAL PORT TO STEREO HP OUTPUT CHARACTERISTICS
Test conditions (unless otherwise specified): “Typical Connection Diagram” on page 17 shows CS42L73 connections (including
Zobel Networks on outputs); Input test signal is a 24-bit full-scale 997-Hz sine wave with 1 LSB of triangular PDF dither applied;
GND = AGND = PGND = CPGND = DGND = 0 V; all voltages are with respect to ground (GND); VA = VCP = 1.80 V; T
A
= +25
C; VCP Mode; Measurement Bandwidth is 20 Hz to 20 kHz; Fs = 48 kHz (Note 10) ; ASP is used and is in slave mode with Fs
ext
= 48 kHz; test loading is configured as per Figure 5 on page 28 (R
L
and C
L
(= C
L(Max)
) as indicated in the table below); Mixer
Attenuation and Digital Volume = 0 dB, Digital and Analog Mutes are disabled.
Parameters (Note 2) Min Typ Max Units
Load R
L
= 16  (Analog Gain = -4 dB) (Note 30)
Dynamic Range
18 to 24-Bit
A-weighted
unweighted
16-Bit A-weighted
unweighted
87
84
85
82 93
90
91
88 -
-
-
- dB
dB
dB
dB
Total Harmonic Distortion + Noise (Note 31) (Note 32) 0 dBFS - -70 -60 dB
Full-scale Output Voltage (Note 32) 0.73•VA 0.79•VA 0.85•VA V
PP
Output Power (Full-scale, Per Channel) (P
OUT
) (Note 32)
2 Channels Driven, THD+N  -60 dB (0.1%) Analog Vol. = -4 dB, Dig. Vol. = 0 dB
2 Channels Driven, THD+N  -40 dB (1%) Analog Vol. = -3 dB, Dig. Vol. = 0 dB
2 Channels Driven, THD+N  -20 dB (10%) Analog Vol. = -1 dB, Dig. Vol. = 0 dB
1 Channel Driven, THD+N  -60 dB (0.1%) Analog Vol. = -2 dB, Dig. Vol. = 0 dB
1 Channel Driven, THD+N  -40 dB (1%) Analog Vol. = -1 dB, Dig. Vol. = 0 dB
1 Channel Driven, THD+N  -20 dB (10%) Analog Vol. = +1 dB, Dig. Vol. = 0 dB
-
-
-
-
-
- 16
20
27
25
32
44 -
-
-
-
-
- mW
mW
mW
mW
mW
mW
Load R
L
= 32  (Analog Gain = -4 dB) (Note 30)
Dynamic Range
18 to 24-Bit
A-weighted
unweighted
16-Bit A-weighted
unweighted
88
85
86
83 94
91
92
89 -
-
-
- dB
dB
dB
dB
Total Harmonic Distortion + Noise (Note 31) (Note 32) 0 dBFS - -81 -75 dB
Full-scale Output Voltage (Note 32) 0.74•VA 0.80•VA 0.86•VA V
PP
Output Power (Full-scale, Per Channel) (P
OUT
) (Note 32)
2 Channels Driven, THD+N  -75 dB (0.018%)Analog Vol. = -4 dB, Dig. Vol. = 0 dB
2 Channels Driven, THD+N  -60 dB (0.1%) Analog Vol. = -1 dB, Dig. Vol. = 0 dB
2 Channels Driven, THD+N  -40 dB (1%) Analog Vol. = 0 dB, Dig. Vol. = -0.5 dB
2 Channels Driven, THD+N  -20 dB (10%)Analog Vol. = +2 dB, Dig. Vol. = -0.5 dB
1 Channel Driven, THD+N  -75 dB (0.018%) Analog Vol. = 0 dB, Dig. Vol. = 0 dB
1 Channel Driven, THD+N  -60 dB (0.1%) Analog Vol. = +1 dB, Dig. Vol. = -0.5 dB
1 Channel Driven, THD+N  -40 dB (1%) Analog Vol. = +1 dB, Dig. Vol. = 0 dB
1 Channel Driven, THD+N  -20 dB (10%) Analog Vol. = +3 dB, Dig. Vol. = -0.5 dB
-
-
-
-
-
-
-
- 8.1
16
17
25
20
23
25
35
-
-
-
-
-
-
-
- mW
mW
mW
mW
mW
mW
mW
mW
Load R
L
= 3 k  (Analog Gain = +2 dB) (Note 30)
Dynamic Range
18 to 24-Bit
A-weighted
unweighted
16-Bit
A-weighted
unweighted
90
87
88
85 96
93
94
91 -
-
-
- dB
dB
dB
dB
Total Harmonic Distortion + Noise (Note 31) (Note 32)
18 to 24-Bit 0 dBFS
-20 dBFS
-60 dBFS
16-Bit 0 dBFS
-20 dBFS
-60 dBFS
-
-
-
-
-
- -85
-73
-33
-83
-71
-31 -79
-
-27
-77
-
-25
dB
dB
dB
dB
dB
dB