Swiftech H20 220 APEX ULTRA PLUS - Manual (Page 10)

Copyright Swiftech 2006 – All rights reserved – Last revision date: 06-19-07 - Information subject to change without notice – URL: http://www.swiftech.com
Rouchon Industries, Inc., dba Swiftech – 3700 Industry Avenue, Suite 104, Lakewood, CA 90712 – Toll free (US): 888-857-9438 – Fax 562-595-8769 - E Mail: help@
Swiftech.com PAGE 10 of 35
Packing List
COMPONENT ID COMPONENT DESCRIPTION QTY USAGE
BHSC006C0-007SS 6-32 X 7/16 BUT HD CAP SS 4.00 WATER-BLOCK ASSEMBLY
O-RING 3/32 B1000-133 O-RING 3/32 X 1 13/1 1.00 WATER-BLOCK ASSEMBLY
APOGEE-H APOGEE WATERBLOCK HOUSING 1.00 WATER-BLOCK ASSEMBLY
APOGEE-BRKT APOGEE HOLD-DOWN PLATE 1.00 WATER-BLOCK ASSEMBLY
APOGEE-BP APOGEE BASE PLATE 1.00 WATER-BLOCK ASSEMBLY
B1000-2.5X50 BUNA-N 70D BLACK O-RING 2.00 FITTINGS
PM4S-6BN 1/4" - 1/8 NPSM TO 3/8" ID 2.00 FITTINGS
PM4S-8BN 1/4" - 1/8 NPSM TO 1/2 ID 2.00 FITTINGS
22HC04688 15/32" HOSE CLAMP 2.00 FITTINGS
22HC0672B 43/64" PREMIUM HOSE CLAMP 2.00 FITTINGS
SPRING6 SPRING FOR MCW6000-775 4.00 COMMON HARDWARE
6-32 HEX CAP 6-32 ACRON NUT 4.00 COMMON HARDWARE
12SWS0444 NYLON SHOULDER WASHER 8.00 COMMON HARDWARE
LOCKWASHER6 LOCK WASHER #6 6.00 COMMON HARDWARE
FW140X250X0215FB BLK BLACK FIBER WASHER .140X.250X. 10.00 COMMON HARDWARE
632.112PHPMS 6X32 X 1 1/2 PHILIPS PAN HEAD 4.00 COMMON HARDWARE
6-32 NUT 6-32 NUT 4.00 COMMON HARDWARE
6-32 X 1 5/8 6-32 X 1 5/8 4.00 XEON SCREWS
WASHER-0148X0266X0040-91007A619 LOCK WASHER #6 X 0.040 4.00 AMD SOCKET 754/939/940,AM2 HARDWARE
90272A153-6-32X1.00-PHILIPS SCREW 6-32 X 1” PHILIPS SCREW 4.00 AMD SOCKET 754/939/940, AM2 HARDWARE
13RS040637 ROUND SPACER 4.00 AMD SOCKET 754/939/940,AM2 HARDWARE
APOGEE-AM2-BP APOGEE AM2 BASE PLATE 1.00 AMD SOCKET AM2 HARDWARE
ARCTIC CÉRAMIQUE ARCTIC CÉRAMIQUE 1.00 THERMAL COMPOUND
Common installation guidelines
Removal of the motherboard is necessary to install the mounting posts in all cases, except for AMD® socket 754,
939, 940 and AM2.
The Apogee water-block may be installed in any direction. Simply rotate the water-block in your hand prior to fasten it
to the processor when you are filling up the circuit. This will purge it from any air bubbles.
The inlet and outlet are interchangeable with respect to flow direction.
Coolant: use of distilled water is mandatory. Swiftech’s HydrX coolant is recommended as an antifungal, and
corrosion inhibitor.
1. Step-by step
Install the fittings with their o-rings into the water block. Tighten each fitting until the flange of the fitting mates with
the ledge of the water-block, then lock it by adding ¼ to ½ turn.
Remove the existing heat sink from your motherboard.
Apply the provided Arctic Céramique thermal compound to the CPU following the comprehensive installation
instructions provided here:
http://www.arcticsilver.com/ceramique_instructions.htm
Install the Apogee water-block following the individual installation schematics for each type of CPU socket provided
hereafter.
Connect the tubing to the water-block hose-barbs. Use the provided hose-clamps to secure the tubing to the barbs.
2. Individual installation schematics
The provided mounting hardware is common to Intel® Pentium® 4 socket 478, socket LGA775, and AMD® socket 462. AMD® socket
754, 939, 940 & AM2 mounting hardware is identified in a separate pack, as well as Intel® Xeon hardware.