Red Lion GEARS - Manual

Sensing Gears are available in a variety of sizes to cover most applications
where a sensor is to be used, but a suitable existing machine gear is not
available. Split-type gears are convenient for use on machine drive shafts where
a shaft-end is not available to mount a standard gear. Hubless gears are ideal for
mounting in tight locations or when only a short shaft stub is available. Hub-
type, Split, and Hubless gears can be supplied with special bores (See notes
below Ordering Information & Dimensions table).
Caution: RLC’s machined steel sensing gears are NOT to be used as driving or
driven gears in a power transmission system.
NO. OF STOCK MAX. SPL. HUB RECOMMENDED RECOMMENDED
TYPE
TEETH & BORE BORE O.D.
DIA “D” PROJ “P”
FACE “F” TORQUE FOR MAXIMUM PART
DIAMETRAL +0.003" +0.003" ±0.003" ±0.010" ±0.020" ±0.010" SET & CAP GEAR NUMBER
PITCH -0.000" -0.000" SCREWS SPEEDS
30 T. 16 D.P. 0.500" 1.375" 2.000" 1.625" 0.500" 0.500" 25 in. lbs. 5000 RPM 0950500
HUB TYPE 60 T. 20 D.P. 0.375" 1.750" 3.100" 2.000" 0.500" 0.375" 25 in. lbs. 5000 RPM 0970375
60 T. 10 D.P. 0.875" 2.250" 6.200" 2.500" 0.875" 1.000" 55 in. lbs. 5000 RPM 0910875
SPLIT GEAR 30 T. 10 D.P. 0.750" 1.875" 3.200" *1.000" 182 in. lbs. 3000 RPM 0920750
60 T. 10 D.P. 0.875" 4.250" 6.200" *1.000" 182 in. lbs. 1500 RPM 0930875
60 T. 20 D.P. 0.625" 0.870" 3.100" 0.375" 25 in. lbs. 5000 RPM 0960625
60 T. 20 D.P. 0.875" 0.875" 3.100" 0.375" 25 in. lbs. 5000 RPM 0960875
HUBLESS 60 T. 12 D.P. 1.125" 1.370" 5.160" 0.656" 40 in. lbs. 5000 RPM 0941125
60 T. 12 D.P. 1.375" 1.620" 5.160" 0.656" 40 in. lbs. 5000 RPM 0941375
60 T. 12 D.P. 1.625" 1.625" 5.160" 0.656" 40 in. lbs. 5000 RPM 0941625
* A portion of the teeth near the cap screws are milled away. However, at least ¼" of the teeth face width is available, allowing sensing of all teeth.
MACHINED STEEL SENSING GEARS FOR EXCITING SENSORS
HUB TYPE GEARS SPLIT GEARS HUBLESS GEARS
SET SCREW
O.D. D
P
F
BORE
SOCKET HEAD
CAP SCREW (2)
LOCK
FLAT
BORE
*F
O.D.
WASHER (2)
SPACER (2)
WASHER
O.D.
F
BORE
SET SCREW
ORDERING INFORMATION & DIMENSIONS
SPECIAL BORES: Hub-Type, Split, and Hubless gears can be supplied with
special bore sizes between the Stock Bore and Max. Special Bore sizes listed
above. To order Special Bores, substitute 9999 for the last 4 digits of the part
number and specify special bore size required.
ASSEMBLY NOTE FOR SPLIT GEARS: When tightening the split gear
halves on a shaft, it is recommended that the flat washer spacers be used to
help keep the gap between halves equal.
Run-out should be checked after installation is complete. Always use the
supplied lock washers when tightening the socket head cap screws. Torque
these screws to 182 in. lbs.
Bulletin No. GRS-J
Drawing No. LP0167
Released 06/13
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net