Hoyles AIDALARM Disabled toilet alarm Stainless Panic Strip Kit - Manual

The AIDALARM is designed as a disabled person alarm The Pull Cord S1600 should be appropriately sited for your
system primarily for use in WCs etc..It is designed to comply
application in the WC or where assistance is required.
with BS 8300 an d the re quirem ents of t he Disa bility Additional pull cords if required are available separately. The
Discrimination Act. lower bangle on the cord should be set at 100mm above floor
level. The second bangle should be set between 800 and
The AIDALARM A600F controller should be sited where staff 1000mm above floor level.
are located who can respond to an emergency call. It needs to The Reset Button S1708SR should be sited near the point of
be powered by a 12vdc power supply (available separately) call and should be mounted with the bottom edge between 800
which should have a standby battery fitted. The power supply and 1000mm above floor level and a minimum of 350mm from
should be rated at a minimum of 250mA. See part numbers any corner.
PSU-12/1A5B and BAT12V3300LA. The system voltage is The Overdoor Light/Sounder S1778SR is usually sited
12vdc thus the ancillary items in toilets or other wet areas are at outside and above the WC door.
a safe working voltage avoiding any conflict with Part P building DADO Panic Strip (Optional) is a normally open device, the
regulations. contacts close when the switch is pressed. Site 150mm from
floor level in WCs.
12vdc Powered AIDALARM A600F Stainless Steel Installation Instructions
Wiring details
Standard 6 core intruder alarm cable or similar is ideal to connect the AIDALARM controller to the ancillary items.
60130 Iss 1 June 2011 T. 01744 886600 F. 01744 886607 E. [email protected] W. www.hoyles.com
Hoyles Electronic Developments Ltd
Operation
Overdoor units are fitted with LEDs and buzzers. Pull Cords are fitted with an LED. Additional units can be fitted if required. Call
buttons S1705SR can also be fitted to give a more flexible operation. Consult our technical dept.
Using the factory default settings, when a call is generated by pulling the cord or by activating any optional call accessory such as
panic strip, audible and visual warning is given at both the WC area and at the AIDALARM control panel. The call can be silenced
at the control panel by pressing the control panel button. This will cause the panel to bleep every 40 seconds as a warning of non
attendance by the responders. The audible indicator at the WC will bleep every five seconds to re-assure the caller. Should the
cord be pulled again while in the Silence state, the system will call again. The system is reset at (or near) the point of call using the
Reset button S1708SR.
Alarm Relay
A single pole change over volt free relay is provided in the control panel. This relay is energised while the system is in its idle state,
when a call is made the relay de-energises, the relay energises again once the call has been reset. The relay also de-energises if
the 12dvc power is lost..
N
O
C
O
M
N
C
B
lu
e
Y e llo
w
W
h it e
ve
-
ve +
ve +
A600F Controller
Located in responders
area
N.O
COM
N.C.
L+ve
L-ve
Pull Cord S1600
Overdoor Light/Buzzer
S1778SR
Located outside WC
Reset Button S1708SR
Located inside WC
Use six core intruder
alarm cable or similar
DADO Panic Strips (optional)
021-485SE
NO
Com
NC
Call
Com
Reset
SDR
-ve
LED
-ve
Fn
Set
Use
[
[
Set Button
Call LED
Power LED
-ve
+ve
-ve
+ve
12vdc input from a
12vdc power supply.
Volt free auxiliary
relay contacts
change on alarm
and mains fail
B
z
-
v
e
+
v
e
L
E
D
-
v
e