KROHNE UFC 400 PROFIBUS PA-PROFIBUS DP - Manual (Page 49)

PROFIBUS SETTINGS
5
49
UFC 400
www.krohne.com 05/2014 - 4003118502 - AD UFC 400 PROFIBUS R02 en
C5.1 Device Info
C5 Device
In this menu all functions are grouped that have no effect on the measurement or any output directly.
C5.1.1 Tag Tag descriptor of the physical block of the PROFIBUS module will be
displayed. The Tag descriptor provides an application specific reference to
the blocks. It will be assigned by the user of the device. The Tag descriptor is
an octet string (a visible string will be preferred) consisting of 32 byte. The
first 21 characters will be displayed only!
C5.3 1st Meas. Page
C5.3.1 Function Specify number of measured value lines (font size)
One Line / Two Lines / Three Lines
C5.3.2 Measurement Line 1 Select the measurement of the 1st line:
Select:
Volume Flow / Velocity of Sound / Mass Flow / Flow Speed / Gain / SNR /
Diag. Flow Speed / Diag. Velocity of Sound / Diag. Gain / Diag. SNR
C5.3.8 Measurement Line 2 Specify measurement of 2nd line (only available if this Line 2 is activated)
Select:
Bargraph / Volume Flow / Velocity of Sound / Mass Flow /
Flow Speed / Gain / SNR / Diag. Flow Speed / Diag. Velocity of Sound /
Diag. Gain / Diag. SNR / FB3 Total. 1 Volume / FB3 Total. 1 Mass /
FB4 Total. 2 Volume / FB4 Total. 2 Mass /
FB5 Total. 3 Volume / FB5 Total. 3 Mass / Operating Hours
C5.3.10 Measurement Line 3 Specify measurement of 3rd line (only available if this Line 3 is activated)
Select:
Volume Flow / Velocity of Sound / Mass Flow / Flow Speed / Gain / SNR /
Diag. Flow Speed / Diag. Velocity of Sound / Diag. Gain / Diag. SNR /
FB3 Total. 1 Volume / FB3 Total. 1 Mass /
FB4 Total. 2 Volume / FB4 Total. 2 Mass /
FB5 Total. 3 Volume / FB5 Total. 3 Mass / Operating Hours
C5.4 2. Meas. page Setting of the measurement for the second measuring page.
For PROFIBUS devices this page shows only the PROFIBUS values
FB1…FB8.
C5.4.1
C5.4.3
C5.4.5
Measurement Line 1
Measurement Line 2
Measurement Line 3
Select the measurement of the 1st, 2nd and 3rd line:
FB1 Analog inp. 1 / FB2 Analog inp. 2 / FB3 Totaliser 1 / FB4 Totaliser 2 /
FB5 Totaliser 3 / FB6 Analog inp. 3 / FB7 Analog inp. 4 / FB8 Analog inp. 5 /
FB9 Analog inp. 6
C5.4.2
C5.4.4
C5.4.6
Format 1.line
Format 2.line
Format 3.line
Fixed number of digits after the decimal point or automatic, where the
number of digits is automatically adjusted to the available space.
C5.8 Physical Block This menu is only available, if a PROFIBUS interface is present.
C5.8.1 Station Address Selects the PROFIBUS station address of the device.
The PROFIBUS address can also be changed using the PROFIBUS service
"set_slave_add". The input range is 0...125 according to the PROFIBUS
specification. Address 126 is the default address and cannot be set via the
PROFIBUS service "set_slave_add" - use menu instead to reset to default
address.
C5.8.7 Information Available if there is a PROFIBUS interface in existence; the below mentioned
information will be displayed about the PROFIBUS interface:
Hardware Revision of the PROFIBUS interface used
Software Version of the PROFIBUS interface used
Date of Compilation
(same as B3.5)
C5.8.2 Diag. extension Content of the PROFIBUS diagnosis extension is displayed.
C5.8.3 Diag. extension i Content of the internal diagnosis extension is displayed.