KROHNE UFC 400 PROFIBUS PA-PROFIBUS DP - Manual (Page 35)

COMMISSIONING / OPERATION
4
35
UFC 400
www.krohne.com 05/2014 - 4003118502 - AD UFC 400 PROFIBUS R02 en
1 Indication is supported if Classic Diagnosis is active only.
2 Indication is supported if Condensed Diagnosis is active only.
3 Indication is supported in cyclic diagnosis only if Ident. Number 4520 or 4521 hex is active.
Nevertheless this information is always available via acyclic access (e.g. by using DD / DTM) for
all Ident. Numbers supported.
yes Indication is supported for all Ident. Numbers.
4 If available readout more detailed diagnosis information using the device display ("Test →
Information → Status Details → …" / menu B3.2) or the PROFIBUS parameter "Device Status
Complete (Slot 0, Index 167)" via "DD"/ "DTM" and try to clear faults displayed.
5 If available readout more detailed diagnosis information using the device display ("Test →
Information → Status Details → …" / menu B3.2) or the PROFIBUS parameter "Device Status
Complete (Slot 0, Index 167)" via "DD"/ "DTM" and try to fix the problem(s) occurred.
6 If available readout more detailed diagnosis information using the device display ("Test →
Information → Status Details → …" / menu B3.2) or the PROFIBUS parameter "Device Status
Complete (Slot 0, Index 167)" via "DD"/ "DTM" and checkout which sort of "Function check" is
running.
7 If available readout more detailed diagnosis information using the device display ("Test →
Information → Status Details → …" / menu B3.2) or the PROFIBUS parameter "Device Status
Complete (Slot 0, Index 167)" via "DD"/ "DTM" to get a more detailed overview about all
additional information just present
8 Detailed information of the PROFIBUS module itself – no more detailed information available.
9 Classification is changeable by the user itself – have a look at chapter "Variable Event Groups".
INFORMATION!
A rough classification of status values according "NE107" is done by using the first character of
the description of a status event:
• F- / ("F-"): Failure (No measurement possible)
• S- / ("S-"): Out of specification (Measurements are available but no longer sufficiently
accurate and should be checked)
• M- / ("M-"): Maintenance required: (Measurements are still accurate but this could change
soon)
• C- / ("C-"): Function check: (A test function is active; the displayed or transferred measured
value does not correspond to the actual measured value)
• I- / ("I-"): Information (not defined by NE107 / device specific): (No direct influence on the
measurements)
INFORMATION!
Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (82) (being contained
Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (82) (being contained Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (82) (being contained Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (82) (being contained
in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group"
in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group" in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group" in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group"
(for detailed information refer to chapter 6.6 "Status messages and diagnostic information" of
(for detailed information refer to chapter 6.6 "Status messages and diagnostic information" of (for detailed information refer to chapter 6.6 "Status messages and diagnostic information" of (for detailed information refer to chapter 6.6 "Status messages and diagnostic information" of
the UFC 400 Handbook). Each "Event group" will consist of up to 32 so called "Single events".
the UFC 400 Handbook). Each "Event group" will consist of up to 32 so called "Single events". the UFC 400 Handbook). Each "Event group" will consist of up to 32 so called "Single events". the UFC 400 Handbook). Each "Event group" will consist of up to 32 so called "Single events".
The diagnosis event bit of an "Event group" will be set if at least one "Single event" belonging to
The diagnosis event bit of an "Event group" will be set if at least one "Single event" belonging to The diagnosis event bit of an "Event group" will be set if at least one "Single event" belonging to The diagnosis event bit of an "Event group" will be set if at least one "Single event" belonging to
this "Event group" will occur. "Single events" occurred can be displayed by using the UFC 400
this "Event group" will occur. "Single events" occurred can be displayed by using the UFC 400 this "Event group" will occur. "Single events" occurred can be displayed by using the UFC 400 this "Event group" will occur. "Single events" occurred can be displayed by using the UFC 400
display menu and/or by using the UFC 400 PROFIBUS DTM or the UFC 400 PROFIBUS EDD in
display menu and/or by using the UFC 400 PROFIBUS DTM or the UFC 400 PROFIBUS EDD in display menu and/or by using the UFC 400 PROFIBUS DTM or the UFC 400 PROFIBUS EDD in display menu and/or by using the UFC 400 PROFIBUS DTM or the UFC 400 PROFIBUS EDD in
conjunction with the appropriate control software (UFC 400 PROFIBUS DTM in conjunction with
conjunction with the appropriate control software (UFC 400 PROFIBUS DTM in conjunction with conjunction with the appropriate control software (UFC 400 PROFIBUS DTM in conjunction with conjunction with the appropriate control software (UFC 400 PROFIBUS DTM in conjunction with
PACTware; the UFC 400 PROFIBUS EDD in conjunction with SIMATIC PDM). An overview of all
PACTware; the UFC 400 PROFIBUS EDD in conjunction with SIMATIC PDM). An overview of all PACTware; the UFC 400 PROFIBUS EDD in conjunction with SIMATIC PDM). An overview of all PACTware; the UFC 400 PROFIBUS EDD in conjunction with SIMATIC PDM). An overview of all
"Single events" supported by UFC 400 can be found in the UFC 400 Handbook.
"Single events" supported by UFC 400 can be found in the UFC 400 Handbook. "Single events" supported by UFC 400 can be found in the UFC 400 Handbook. "Single events" supported by UFC 400 can be found in the UFC 400 Handbook.