KROHNE UFC 400 PROFIBUS PA-PROFIBUS DP - Manual (Page 33)

COMMISSIONING / OPERATION
4
33
UFC 400
www.krohne.com 05/2014 - 4003118502 - AD UFC 400 PROFIBUS R02 en
65 3 M – Configuration
(classification fixed - not changeable)
Configuration related problem(s) detected. But still the
measurement values are accurate. The output values are still
valid, but this may change in the near future. Check problem(s) /
5 - if the problem(s) cannot be fixed contact the service
department of the manufacturer with an indication of the
problem(s).
66 3 M – Electronics
(classification fixed - not changeable)
Converter Electronic related problem(s) detected. But still the
measurement values are accurate. The output values are still
valid, but this may change in the near future. Check problem(s) /
5 - if the problem(s) cannot be fixed contact the service
department of the manufacturer with an indication of the
problem(s).
67 3 M – Sensor
(classification fixed - not changeable)
Sensor related problem(s) detected. But still the measurement
values are accurate. The output values are still valid, but this may
change in the near future. Check problem(s) / 5 - if the
problem(s) cannot be fixed contact the service department of the
manufacturer with an indication of the problem(s).
68 3 S – Process
(classification fixed - not changeable)
Process related fault(s) detected. E.g. the device may be operated
outside its specified operating range. The measurement accuracy
may be reduced. But still the measurement value follows the
source. Check fault(s) detected / 4 - if the fault(s) cannot be
cleared contact the service department of the manufacturer with
an indication of the problem(s).
69 3 S – Configuration
(classification fixed - not changeable)
Configuration related fault(s) detected. E.g. the device may be
operated outside its specified operating range. The measurement
accuracy may be reduced. But still the measurement value
follows the source. Check fault(s) detected / 4 - if the fault(s)
cannot be cleared contact the service department of the
manufacturer with an indication of the problem(s).
70 3 S – Electronics
(classification fixed - not changeable)
Converter Electronic related fault(s) detected. E.g. the device may
be operated outside its specified operating range. The
measurement accuracy may be reduced. But still the
measurement value follows the source. Check fault(s) detected /
4 - if the fault(s) cannot be cleared contact the service
department of the manufacturer with an indication of the
problem(s).
71 3 S – Sensor
(classification fixed - not changeable)
Sensor related fault(s) detected. E.g. the device may be operated
outside its specified operating range. The measurement accuracy
may be reduced. But still the measurement value follows the
source. Check fault(s) detected / 4 - if the fault(s) cannot be
cleared contact the service department of the manufacturer with
an indication of the problem(s).
72 3 ("I-") Electr: Power Failure
(default classification / 9)
Information only; e.g. power-down detected / 7. Just information.
No impact on measurement expected.
74 3 ("S-") Config_ Totalizer
(default classification / 9)
Configuration related fault(s) detected concerning totalizer. E.g.
"Overflow" of a totalizer – counting starts with "zero". The
measurement accuracy may be reduced. But still the
measurement value follows the source. Check fault(s) detected /
4 - if the fault(s) cannot be cleared contact the service
department of the manufacturer with an indication of the
problem(s).
75 3 ("S-") Proc: Signal unreliable
(default classification / 9)
Process related fault(s) detected concerning the "sensor". E.g.
not reached accuracy. The measurement accuracy may be
reduced. But still the measurement value follows the source.
Check fault(s) detected / 4 - if the fault(s) cannot be cleared
contact the service department of the manufacturer with an
indication of the problem(s).
Bit Number sup
p
orted
De
sc
ription
Remedy