KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.4.08 to 4.11 - Manual (Page 155)

BOP-1K 070212
B-1
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 INTRODUCTION
This appendix defines the SCPI subsystem commands and queries used with the BOP power sup-
ply. Subsystem commands are defined in PAR. B.3 through B.150, arranged in groups as they
appear in the tree diagram, Figure 3-18. Table B-1 provides a quick reference of all SCPI subsys-
tem commands and queries used in the BOP.
TABLE B-1. SCPI SUBSYSTEM COMMAND/QUERY INDEX
COMMAND PAR. COMMAND PAR.
ABOR B.3 [SOUR:]LIST:CURR, ? B.54, B.55
CAL B.4 [SOUR:]LIST:CURR:APPL B.56
INIT[:IMM] B.5 [SOUR:]LIST:CURR:APPL:SWE, ? B.57, B.58
INIT:CONT, ? B.6, B.7 [SOUR:]LIST:POIN? B.59
MEAS:CURR? B.8 [SOUR:]LIST:DIV, ? B.60, B.61
MEAS:MODE B.9 [SOUR:]LIST:DWEL, ? B.62, B.63
MEAS:VOLT? B.10 [SOUR:]LIST:DWEL:POIN? B.64
MEAS:TRAN? B.11 [SOUR:]LIST:QUER, ? B.65, B.66
MEM:UPD B.12 [SOUR:]LIST:REP B.67
OUTP[:STAT], ? B.13, B.14 [SOUR:]LIST:RES? B.68
OUTP:CONT ? B.15, B.16 [SOUR:]LIST:SAMP:CURR B.69
OUTP:MODE, ? B.17, B.18 [SOUR:]LIST:SAMP:VOLT B.70
[SOUR:]CURR, ? B.19, B.20 [SOUR:]LIST:SAMP? B.71
[SOUR:]CURR:LIM[:BOTH], ? B.21, B.22 [SOUR:]LIST:SET:SAMP, ? B.72, B.73
[SOUR:]CURR:LIM:NEG, ? B.26, B.24 [SOUR:]LIST:SET:TRIG, ? B.74, B.75
[SOUR:]CURR:LIM:POS, ? B.26, B.26 [SOUR:]LIST:SET:WAIT, ? B.76, B.77
[SOUR:]CURR:MODE, ? B.27, B.28 [SOUR:]LIST:TRIG: B.78
[SOUR:]CURR:PROT[:BOTH], ? B.29, B.30 [SOUR:]LIST:VOLT, ? B.79, B.80
[SOUR:]CURR:PROT:MODE, ? B.31, B.32 [SOUR:]LIST:VOLT:APPL B.81,
[SOUR:]CURR:PROT:NEG, ? B.33, B.34 [SOUR:]LIST:VOLT:APPL:SWE, ? B.82, B.83
[SOUR:]CURR:PROT:POS, ? B.35, B.36 [SOUR:]LIST:VOLT:POIN? B.84
[SOUR:]CURR:PROT:LIM[:BOTH], ? B.37, B.38 [SOUR:]LIST:WAIT:HIGH B.85
[SOUR:]CURR:PROT:LIM:NEG, ? B.39, B.40 [SOUR:]LIST:WAIT:LEDG B.87
[SOUR:]CURR:PROT:LIM:POS, ? B.41, B.42 [SOUR:]LIST:WAIT:LOW B.87
[SOUR:]CURR:TRIG, ? B.43, B.44 [SOUR:]VOLT, ? B.88, B.89
[SOUR:]FUNC:MODE, ? B.45, B.46 [SOUR:]VOLT:LIM[:BOTH], ? B.90, B.91
[SOUR:]FUNC:MODE:TRIG, ? B.47, B.48 [SOUR:]VOLT:LIM:NEG, ? B.92, B.93
[SOUR:]LIST:CLE B.49 [SOUR:]VOLT:LIM:POS, ? B.94, B.95
[SOUR:]LIST:COUN, ? B.50, B.51 [SOUR:]VOLT:MODE, ? B.96, B.97
[SOUR:]LIST:COUN:SKIP, ? B.52, B.53 [SOUR:]VOLT:PROT[:BOTH], ? B.98, B.99
NOTE: Commands listed above that are followed by “, ?“ have a related query.